User manual SENTROL ZXLED12

[. . . ] How to Use Your Moose Security System ZXLED8/ZXLED1 2 Control Station READY TROUBLE FIRE 1 5 9 2 6 10 3 7 11 4 8 12 VIEW INFO ALM MEM EVENT LOG OFF CANCEL D 1 BYPASS 2 DELAY ARM 3 CHIME 4 AWAY RST SMOKE 5 TEST 6 PROGRAM 7 QUIT 8 ACCESS 9 INSTANT STAY CLEAR HOME 0 B ENTER NEXT NIGHT A C PREV 1 (ZXLED12 shown) INTRODUCTION Thank you for choosing the ZX200/ZX210 or ZX400/ZX410 Security Control. This control will provide you with years of reliable operation when properly installed and maintained. To maximize the benefits of your Security System, it is important to carefully read the entire contents of this manual and become familiar with all control operations. Your Security Company Representative has recorded confidential information about your system in this manual, therefore, you should store it in a secure place. [. . . ] 4. Press 6 . Enter a number between 13 and 28 to select a wireless sensor to test. See Protection Zones for a list of zone numbers and descriptions. The Control Station will indicate the signal strength by: Error Tone One Beep (the selected zone is not RF or is missing) (call your installation representative) Three Beeps (acceptable) Five Beeps 5. (strong) Repeat step 4 or press CLEAR to exit. 24 OPTIONAL FEATURES ZX200/ZX210 PROGRAMMING ZX200/ZX210 Programming Your system has several features which you may be able to program yourself. DO NOT attempt to program the system unless you have been properly trained on programming procedures and you fully understand these operations. There are two (2) options available: 1 Remote Connect Allows the installer to program and diagnose problems from a remote site using the telephone lines. Allows you to change any passcodes. 2 Program User Codes Remote Connect Contact your Security Company Representative for instructions. Programming the User Passcodes Your system may be programmed with up to 9 user passcodes. Consult your Security Company Representative as to which passcodes have been enabled and what Authority Level has been assigned to each one. Press 9 . 2. Enter passcode: . The Ready and Trouble LEDs will flash. 3. Press 2 . 25 ZX200/ZX210 PROGRAMMING 4. Enter the User Passcode ID program/change. (1 - 9) that you wish to 5. Press ENTER . 6. Enter new four-digit passcode: . Repeat steps 4 - 6 for each passcode to be programmed or press CLEAR to return to the Ready mode. If the new passcode being entered is a duplicate of an existing one, the Control Station will sound an error tone and return to the first digit location so you may try again. If you wish to make a User ID passcode inoperable, enter 0 0 0 0 as the new four-digit passcode. 26 OPTIONAL FEATURES ZX400/ZX410 PROGRAMMING ZX400/ZX410 Programming Your system has several features which you may be able to program yourself. DO NOT attempt to program the system unless you have been properly trained on programming procedures and you fully understand these operations. There are seven (7) options available: 1 Remote Connect Allows the installer to program and diagnose problems from a remote site using the telephone lines. (Military format) Schedules your system to automatically turn ON at a specific day(s) and time(s). Allows you to change any passcodes. 2 3 4 5 6 Set Clock Program Automatic-ON Program Latch Key Program User Codes Cancelling Automatic-ON Cancels the system from automatically For Today turning ON for the scheduled time for that day only. Cancelling Exit-ON For Today Cancels the system from automatically turning ON for Today 10 minutes after you leave the premises for that day only. 7 Remote Connect Contact your Security Company Representative for instructions. 27 ZX400/ZX410 PROGRAMMING Set Clock The clock is set according to military time (24:00 hours). Press 9 . 2. Enter passcode: The Ready and Trouble LEDs will flash. . 3. Press 2 . Set the new time and date (see example). EXAMPLE: To set the clock to 2:15 pm on June 17, 1997: Press 1 0 4 6 1 5 (2:15 pm) Press 1 7 9 7 (June 17, 1997) 4. Press CLEAR to start over if a mistake is made or press ENTER to save changes. 28 OPTIONAL FEATURES ZX400/ZX410 PROGRAMMING Programming the Automatic-ON Feature (DO NOT enable for UL Listed Systems) This feature allows you to automatically turn your system ON at certain times for certain days. There are four items to be programmed: A. Setting the Security Level Day(s) of week to automatically turn ON Hour to turn ON each day Minute to turn ON each day A. Setting the Security Level To program the Automatic-ON feature: 1. Press 9 . 2. Enter passcode: The Ready and Trouble LEDs will flash. . 3. Press 3 1 . 4. Press (for location 1). 5. Press ENTER . 6. Press 0 for AWAY, press 1 for STAY, or press 2 for NIGHT. [. . . ] · Increase the separation between the equipment and the receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or and experienced radio/TV technician for help. CAUTION: Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. 61 FCC COMPLIANCE OPTIONAL FEATURES Canadian Notice The Canadian Department of Communications label identifies certified equipment. [. . . ]