User manual SHARP 2430

[. . . ] See Figure 1 (for 24") or Figures 3 and 4 (for 30") . UNPACKING YOUR MICROWAVE DRAWER · Remove all packing materials from inside the Microwave Drawer. DO NOT REMOVE THE WAVEGUIDE COV ER, which is located on the top of t he M icrowave Drawer. Sealing surface Waveguide cover IMPORTANT NOTES TO THE CONSUMER Keep this manual with your Operation Manual for future reference. · As when using any microwave oven generating heat, there are certain safety precautions you should follow. [. . . ] Pay special attention to the floor on which the Microwave Drawer will sit. The floor of the opening should be constructed of plywood strong enough to support the weight of the oven (about 100 pounds). · Be sure that the clearance of the floor between the wall oven · The microwave interior will easily accommodate a 9" x 13" oblong dish or a bag of microwave popcorn. 24" MICROWAVE DRAWER MEASUREMENTS Electrical outlet location 5" 4" (6") Anti-Tip block 3 1/2" 14 13/16" to bottom Allow 3/16" of Anti-Tip overlap. block 14 13/16" opening Allow 7/16" overlap. Floor must support 100 lbs. 22 1/8" opening Allow 7/8" overlap. 36" countertop height 23 1/2" Allow 7/8" min depth overlap. 19" to top of floor Figure 1 24" cabinet min. Figures 1 and 2 contain many Microwave Drawer measurements for reference when planning the drawer's location. 4 11/16" 1 23/32" 21 19/32" 15 13/32" 15" auto drawer opening 14 19/32" 23 3/8" Figure 2 1 13/16" door thickness 23 7/8" 2 30" MICROWAVE DRAWER MEASUREMENTS Electrical outlet location 5" 4" Allow 1/4" overlap. 14 3/4" opening Allow 7/16" overlap. 6" Anti-Tip block 3 1/2" 28 7/16" opening Allow 3/4" overlap. 36" countertop height Optional wall oven cutout illustrated in sketch Electrical outlet location (6") 14 13/16" to bottom of Anti-Tip block 23 1/2" min depth 84" wall cabinet Floor must support 100 lbs. 19" to top of floor (recommended) Anti-Tip block 3 1/2" 5" 28 7/16" opening Allow 3/4" overlap. 14 3/4" opening Allow 7/16" overlap. Figure 4 30" cabinet min. 14 13/16" to bottom of Anti-Tip block Floor must support 100 lbs. Figures 3, 4 and 5 contain many Microwave Drawer measurements for reference when planning the drawer's location. 4 11/16" 28 1/8" 23 1/2" min depth Allow 3/4" overlap. 2" 15 13/32" 19" to top of floor (recommended) 15" auto drawer opening 23 3/8" 14 3/4" 30" cabinet min. Figure 3 Figure 5 30" ANTI-TIP BLOCK NORMAL INSTALLATION STEPS ANTI-TIP BLOCK INSTALLATION INSTRUCTIONS totally stable. When fastening, be sure that the screws do not penetrate electrical wiring or plumbing. (6") Anti-Tip block 5" To reduce the risk of tipping of the drawer, the Anti-Tip block must be properly installed located Electrical outlet location the floor 14 3/4-inches above on which the Microwave Drawer will sit. The 6-inch Anti-Tip block must be provided by the installer. See Figures 1 and 6 (for 24") or Figures 3, 4 and 6 (for 30"). The Anti-Tip block prevents serious injury that might result from spilled hot liquids. If the Microwave Drawer is ever moved to a different location, the Anti-Tip block must also be moved and installed. [. . . ] Do not use an extension cord. Grounding pin 3-Prong receptacle Ground receptacle box MODEL AND SERIAL NUMBER LOCATION For models KB-6015K and KB-6002L The name plate, including model and serial number, is located Temporary behind the Microwave Drawer front. on the faceplate Use The name plate includes model and serial number. The label is slightly beyond the back wall Screw of the microwave cavity facing up from the flat surface. Tab for grounding screw Ground receptacle box For model KB-6014L Grounding adapter CARE, CLEANING AND MAINTENANCE BEFORE YOU CALL FOR SERVICE Refer to the Operation Manual for cleaning instructions. Read the BEFORE YOU CALL and operating instruction sections in your Operation Manual. [. . . ]