User manual SHARP 59CS-03IR DOCUMENT

[. . . ] Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. ASA DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below: IMPORTANT: The wires in the mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: · The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black. [. . . ] You can set language and country the same as in the Initial auto installation (Analogue). (See page 7. ) TV only Programme Setup This section describes how to set up analogue TV channels manually. 1 2 3 Press MENU and the MENU screen displays. Press a/b to select "Programme Setup", and then press OK. If you have already set the PIN under "Child Lock", enter it here. · See page 14 for setting PIN. 4 Press a/b to select "Auto Search", "Manual Adjust", "Sort" or "Erase Programme", and then press OK. Auto Search Manual Adjust Sort Erase Programme No Yes 12 Menu operations G Auto Search You can automatically search for and download TV channels by performing the procedure below. This is the same function as from programme auto search to auto sorting in Auto Installation. Colour sys. Select the optimum colour systems to receive. (AUTO, PAL, SECAM) NOTE · If "Auto" is selected, colour system for each channel is automatically set. If an image does not display clearly, select another colour system (e. g. PAL, SECAM). 1 2 Repeat steps 1 to 4 in Programme Setup. Press a/b to select "Yes", and then press OK. Sound sys. (Broadcasting system) Select the optimum sound systems (Broadcasting systems) to receive. Press a/b/c/d to select the channel you want to move, and then press OK. Press a/b/c/d to move it to the desired position, and then press OK. Repeat steps 3 and 4 until all desired channels are sorted. 1 2 3 Repeat steps 1 to 3 in Changing the PIN. Press a/b to select "Reset", and then press OK. Press a/b to select "Yes", and then press OK. NOTE · As a precautionary measure, make a note of your PIN on the back of this operation manual, cut it out and keep it in a safe place that children cannot reach. · See page 25 for resetting the current PIN to the factory preset "1234" if you lose or forget your PIN. · To relock a channel which has been temporarily unlocked by inputting the correct PIN, turn power off and then on again. G Erase Programme An individual programme can be erased. 1 2 3 4 5 Repeat steps 1 to 4 in Programme Setup. Press a/b to select "Yes", and then press OK. Press a/b/c/d to select the channel you want to erase, and then press OK. Press OK to erase the selected programme. Repeat steps 3 and 4 until all desired channels are erased. TV only Input Label You can assign each input source a label you like. 1 2 3 4 5 Press b to select the desired input source. [. . . ] Wait until the PC receives the OK response before sending the next command. WIDE MODE WI WI WI WI WI WI WI WI DE0 DE1 DE2 DE3 DE4 DE5 DE6 DE8 Command format Eight ASCII codes e CR C1 C2 C3 C4 P1 P2 P3 Command 4-digits P4 Return code MUTE MUTE0 MUTE1 MUTE2 Parameter 4-digits Command 4-digits: Command. Parameter 4-digits: Parameter 0 ­ 9, g, blank, ? AUDIO CHANGE SLEEP TIMER ACHA_ OFTM0 OFTM1 OFTM2 OFTM3 OFTM4 OFTM5 Parameter Input the parameter values, aligning left, and fill with blank(s) for the remainder. (Be sure that four values are input for the parameter. ) When the input parameter is not within an adjustable range, "ERR" returns. (Refer to "Response code format". ) TEXT TEXT0 TEXT1 DCPG* 0 0 0 0 9 ­ 1 3 0 0 0 0 0 5 5 NOTE · If an underbar (_) appears in the parameter column, enter a space. [. . . ]