User manual SHARP AF-W18CME

[. . . ] AF-W18CME ROOM AIR CONDITIONER INSTALLATION AND OPERATION MANUAL CONTENTS PAGE OPERATION INSTRUCTIONS · PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 · ADDITIONAL NOTES ON OPERATION . . 3 · CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 · USING THE REMOTE CONTROL . . . . . . . . . . . [. . . ] Also, protect the unit and remote control from moisture and shock which can discolour or damage them. 5 BASIC OPERATION 1 Press the MODE button to select the operation mode. AUTO COOL DRY MODE FAN TEMP. TIMER TEMP. 2 3 2 5 3 1 4 Press the ON/OFF button to start operation. · The red OPERATION lamp on the unit will light up. Press the THERMO. · In the AUTO and DRY mode, the temperature can be changed in 1°C increments within the range of 2°C higher to 2°C lower from the temperature automatically determined by the air conditioner. · In the COOL mode, the temperature can be set within the range of 18 °C to 32 °C. AUTO/DRY MODE SAVE MODE 1H FAN SWING CANCEL COOL MODE 4 Press the FAN button to set the desired fan speed. AUTO SOFT LOW HIGH · In the DRY mode, the fan speed is preset to AUTO and cannot be changed. 5 TIPS ABOUT AUTO MODE To turn off the unit, press the ON/OFF button again. · The red OPERATION lamp on the unit will turn off. In the AUTO MODE, the temperature setting and mode are automatically selected depending on the room temperature when the unit is turned on. Room temperature at start up Mode Preset temperature COOL DRY Room Temp. NOTE: When the room temperature drops during cooling or dry operation, the operation may turn to fan mode or the operation may stop automatically. 6 AIR FLOW AND VENTILATION LEFT/RIGHT AIR FLOW ADJUSTMENT Adjust the louvers to change the direction of air flow. Press the SWING button on the remote control, and the Left/Right air flow adjustment louvers will swing continuously. You can adjust the air flow to your desired direction. Never attempt to move the Left/Right air flow adjustment louvers manually, or manually force the louver movement to stop during swing operation. Left/Right air flow adjustment louvers (Automatic) SWING UP/DOWN AIR FLOW ADJUSTMENT Airflow direction can be adjusted by moving the airflow adjustment louvers upward or downward. To avoid condensation on the louvers, please do not adjust these louvers to extremely downward position during COOL and DRY modes. Up/Down air flow adjustment louvers VENTILATION LEVER If air in your room is stale, set the VENTILATION lever to the RIGHT (OPEN) position. This will remove stale air from the room. The VENTILATION lever should normally be kept in the LEFT (CLOSED) position during cooling operation for maximum cooling effect. Ventilation lever CLOSED OPEN 7 TIMER OPERATION TIMER OFF The unit will turn off automatically according to your setting. Timer duration can be set from minimum 0. 5 hours (30 minutes) to maximum 12 hours. Up to 9. 5 hours, you can set by 0. 5 hours (30 minutes) increments and from 10 to 12 hours, by 1 hour increment. MODE FAN TEMP. TIMER TEMP. 1 Pressasthe TIMER OFF ( time desired. 0. 5H 1. 0H 1. 5H ) button and set · The time setting will change as you to press the button as follows, 10H 11H 12H SAVE MODE 1H FAN SWING CANCEL 1 Hold the button pressed down for fast setting. · The yellow TIMER lamp on the unit will light up. · The unit will generate a beep when it receives the signal. · The time setting will count down to show remaining time. Example : When you wish to stop the operation 2. 5 hours later. TIPS ABOUT TIMER OFF OPERATION When the TIMER OFF is set, the temperature setting is automatically adjusted to prevent the room from becoming excessively cold while you sleep. (Auto Sleep function) TO CANCEL TIMER Press the CANCEL button. · The yellow TIMER lamp on the unit will turn off. SAVE MODE 1H FAN SWING CANCEL COOL/DRY MODE: · One hour after the timer operation begins, the temperature setting rises 1°C higher than the original thermostat setting. TO CHANGE TIMER SETTING Press the TIMER button which you wish to change, (TIMER OFF or TIMER ON) and change the time setting. 8 TIMER ON The unit will turn on automatically according to your setting. Timer duration can be set from minimum 0. 5 hours (30 minutes) to maximum 12 hours. [. . . ] (Fig. 3) Front panel 1 Fig. 3 2 (1) Unscrew the 2 stopper screws at the back of the cabinet. (Fig. 4) Unscrew the stopper screw from the angle at the front of the chassis. Slide the angle to the left and remove the angle. (Fig. 4) Keep the screw and angle as they will be used later in Step 6. [. . . ]