User manual SHARP AH-AP09CF/AP12CF

[. . . ] R MODELS AH -AP09CF AH -AP12CF SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL INDOOR UNIT OUTDOOR UNIT AH-AP09CF AH-AP12CF AU-A09BF AU-A12BF Thank you for purchasing a SHARP air conditioner. Please read this manual carefully before operating the product. CONTENTS · PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1 · ADDITIONAL NOTES ON OPERATION . . . . . . . . . E-3 · TIPS ON SAVING ENERGY . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (Thermostat) Button 5 DISPLAY Button FAN TIMER TEMP. 3 6 MODE Button 7 TIMER ON Button (for setting the timer) 4 DISPLAY MODE 1h FAN SWING CANCEL 8 ONE-HOUR OFF TIMER Button 9 TIMER OFF Button (for setting the timer) 0 FAN Button q TIMER CANCEL Button w SWING Button e PLASMACLUSTER Button 5 6 7 8 9 0 q w e L. C. D. REMOTE CONTROL DISPLAY r MODE SYMBOLS : AUTO : DRY t FAN SPEED SYMBOLS : AUTO y PLASMACLUSTER SYMBOL u TEMPERATURE AND TIMER COUNT DOWN INDICATOR i TRANSMITTING SYMBOL o TIMER ON/TIMER OFF INDICATOR Indicates when timer on or timer off is set. : COOL : FAN ONLY r : Manual setting t y u i o E-5 USING THE REMOTE CONTROL LOADING BATTERIES Use two size-AAA (R03) batteries. the battery cover 1 Removethe remote control. at the back of compartment, 2 Insert batteries in the± and -- making sure the polarities are correctly aligned. · Lines will be indicated on the display when batteries are properly installed. 3 Reinstall NOTES: the battery cover. Remote control cover · The battery life is approximately one year in normal use. · When you replace the batteries, always change both batteries, and make sure they are the same type. · If the remote control does not operate properly after replacing the batteries, take out the batteries and reinstall them again after 30 seconds. · If you will not be using the unit for a long time, remove the batteries from the remote control. HOW TO USE THE REMOTE CONTROL Point the remote control towards the unit's signal receiver window and press the desired button. The unit generates a beep when it receives the signal. · Make sure there is no curtain or other object between the remote control and the unit. · The remote control can send signals from up to 7 metres away. CAUTION · Do not allow the signal receiver window to receive strong direct sunlight, since it can adversely affect its operation. If the signal receiver window is exposed to direct sunlight, close a curtain to block the light. · Using a fluorescent lamp with a quick starter in the same room may interfere with transmission of the signal. · The unit can be affected by signals transmitted from the remote control of a television, VCR or other equipment used in the same room. · Do not leave the remote control in direct sunlight or near a heater. Also, protect the unit and remote control from moisture and shock which can discolour or damage them. E-6 TIPS ABOUT PLASMACLUSTER OPERATION The ionizer inside the air conditioner will release cluster ions, which are collective mass of positive and negative ions, into the room. The cluster ions reduce airborne mold fungus and deodorize/decompose odorcausing molecules. Ionizer Cluster ions Mold fungus Odor Eliminate, deodrize, decompose AIR CLEAN OPERATION Cluster ions released into the air will keep your room air clean. REFRESHING OPERATION Negative cluster ions which also exist in natural environment will be released into the air of your room in an increased rate, and help your physical and mental refreshment. Please refer to page 11 for operation. E-7 BASIC OPERATION 1 Press the MODE button to select the operation mode. AUTO COOL DRY FAN ONLY MODE TEMP. 2 2 5 3 1 4 Press the ON/OFF button to start operation. · The red OPERATION lamp ( unit will light. ) on the FAN TIMER TEMP. 3 Press the THERMO. button to set the desired temperature. AUTO/DRY MODE The temperature can be changed in 1°C increments within the range of 2°C higher to 2°C lower from the temperature automatically determined by the air conditioner. COOL MODE The temperature can be set within the range of 18 to 32°C. FAN ONLY MODE The temperature setting cannot be made. DISPLAY MODE 1h FAN SWING CANCEL 4 Press the FAN button to set the desired fan speed. AUTO SOFT LOW HIGH · In the DRY mode, the fan speed is preset to AUTO and cannot be changed. · In the FAN ONLY mode, the fan speed cannot be set to AUTO. 5 To turn off the unit, press the ON/OFF button again. · The red OPERATION lamp ( unit will turn off. ) on the E-8 TIPS ABOUT AUTO MODE In the AUTO mode, the temperature setting and mode are automatically selected according to the room temperature when the unit is turned on. [. . . ] button is pressed during normal operation, the unit will turn off. E-14 MAINTENANCE Be sure to disconnect the power cord from the wall outlet or turn off the circuit breaker before performing any maintenance. CLEANING THE FILTERS The air filters should be cleaned every two weeks. 1 TURN OFF THE UNIT 2 REMOVE THE FILTERS 1 2 3 1 Lift the open panel. 2 Push the air filters up slightly to unlock them. 3 Pull the air filters down to remove them. If the filters are dirty, wash them with warm water and a mild detergent. [. . . ]