User manual SHARP AL-1600

[. . . ] MODEL AL-1600 AL-1610 DIGITAL COPYING MACHINE OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · STATUS INDICATORS 2 15 24 · GENERAL INFORMATION 32 FOR YOUR PROTECTION. . . To aid in reporting this compact copier in case of loss or theft, please record below the model number and serial number located on the back of the unit. We also suggest you record all the information listed and retain for future reference. MODEL NUMBER DATE OF PURCHASE Dealer Address State Service Station Address State Zip City Telephone Zip City Telephone SERIAL NUMBER For location of the nearest Sharp Authorized Service, or to obtain product literature, accessories, or supplies, please call 1-(630)378-3590 in the USA or Toll Free 1-877-SHARP-CC in Canada. For customer assistance, please visit http://www. sharpusa. com (for USA) or http://www. sharp. ca (for Canada) on the World Wide Web or call 1-(630)378-3590 (for USA). CONTENTS INTRODUCTION This copier has been designed to provide convenient copying features in a minimum amount of office space and with maximum operational ease. [. . . ] Misfeed in the transport area 1 Open the paper guide by pressing down the projection on either side of the guide and remove the misfed paper. The fusing unit is hot. Take care in removing paper. 2 If the misfed paper cannot be removed by the previous step but is visible in the paper output area, remove the paper by pulling it into the paper output area. 30 MISFEED REMOVAL 3 Close the side cover by pressing the handle on the cover. q The misfeed ( ) indicator will go out. Misfeed in the paper tray Before opening the paper tray, be sure to open the bypass tray, lift slightly on the side cover and slide the cover out until it stops, and then perform steps 1 to 3 described in the "A. Misfeed in the paper feed area" section. 1 2 Gently lift and pull out the paper tray and remove the misfed paper. Close the paper tray. STATUS INDICATORS 3 Lift slightly on the side cover and slide the cover out until it stops. Close the side cover by pressing the handle on the cover. q Misfeed removal The misfeed ( ) indicator will go out. 31 USER PROGRAMS The user programs allow the parameters of certain functions to be set, changed, or canceled as desired. List of user programs This copier has the following user programs. Program name 1 Auto clear time Description Sets the auto clear time. The copier returns to the initial settings when the auto clear time elapses after the last copy is made. Sets the time that elapses before the copier enters the preheat mode after any operation is made. Sets the time that elapses before the copier enters the auto power shut-off mode after any operation is made. Enables or disables the auto power shut-off mode. See page 34. 2 Preheat mode 3 Auto power shut-off timer Auto power shut-off setting Paper size setting 5 21 Sets the copy paper size in the tray. Setting the user programs 1 User programs Press and hold the light ( ) key for more than 5 seconds until all the alarm indicators ( , , , and ) blink and "­ ­" appears in the copy quantity display. 2 GENERAL INFORMATION Enter a program number using the left copy quantity ( ) key. q q The selected program number will blink in the copy quantity display. If a mistake is made in steps 2 to 4, press the CLEAR ( copier will return to step 2. The program numbers are shown in the table above. For example, to change the setting of the auto power shut-off timer, enter 3. The q 3 Press the START ( q ) key. The entered program number will be steadily lit on the left side of the copy quantity display and the currently selected parameter number for the program will blink on the right side. 32 USER PROGRAMS 4 Select the desired parameter using the right copy quantity ( ) key. q The entered parameter number will blink on the right side of the copy quantity display. The parameters are shown in the table below. For example, to change the setting of the auto power shut-off timer to 60 min. , enter 2. q Program name Auto clear time Preheat mode Auto power shut-off timer Auto power shut-off setting Paper size setting Parameters 0 e OFF 1 e 30 sec. 0 e OFF * 1 e ON 1 e 11"x17" 2 e 8-1/2"x14" * 3 e 8-1/2"x11" 4 e 8-1/2"x11"R 5 e 5-1/2"x8-1/2" Factory default settings are indicated with an asterisk (*). If you select "0" (OFF) in a program, the corresponding function will be disabled. User programs 5 Press the START ( q ) key. GENERAL INFORMATION The right-hand number in the copy quantity display will be steadily lit and the entered value will be stored. 6 To continue with other user programs, press the CLEAR ( ) key and then repeat steps 2 to 5. To exit the user program mode, press the light ( ) key. q All the alarm indicators will go out. 33 POWER SAVE MODES The copier has two power save modes to reduce overall power consumption thereby reduce the cost of operation. In addition, these modes conserve natural resources and help reduce environmental pollution. The two power save modes are preheat mode and auto power shut-off mode. q User programs The preheat activation time and the auto power shut-off time have been preset at the factory to 90 sec. [. . . ] This classification is given to chemicals for which there is inadequate human evidence, but sufficient animal evidence on which to base an opinion of carcinogenicity. The classification is based upon the development of lung tumors in rats receiving chronic inhalation exposures to free carbon black at levels that induce particle overload of the lung. Studies performed in animal models other than rats did not show any association between carbon black and lung tumors. While there have been no studies to date using developer, a two-year cancer bioassay using a typical toner preparation containing carbon black (a small amount of toner is included in the developer mixture) demonstrated no association between toner exposure and tumor development in rats. [. . . ]