User manual SHARP AL-1641CS

[. . . ] MODEL AL-1631 AL-1641CS DIGITAL LASER COPIER DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL Page INTRODUCTION SETTING UP THE UNIT LOADING PAPER INSTALLING THE SOFTWARE (AL-1641CS) MAKING COPIES SPECIAL FUNCTIONS MAINTENANCE TROUBLESHOOTING THE UNIT APPENDIX 4 7 14 19 46 52 57 61 68 AL-1631/AL-1641CS FOR YOUR PROTECTION. . . To aid in reporting this unit in case of loss or theft, please record below the model number and serial number located on the back of the unit. We also suggest you record all the information listed and retain for future reference. MODEL NUMBER DATE OF PURCHASE Dealer Address State Service Station Address State Zip City Telephone Zip City Telephone SERIAL NUMBER To obtain service, or to obtain product literature, accessories, or supplies, please call or 1-(630)378-3590 in the USA 905-568-7140 in Canada. For customer assistance, please visit http://www. sharpusa. com/ (for USA) or http://www. sharp. ca/ (for Canada) on the World Wide Web or call 1-(630)378-3590 (for USA). Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from copying by national law. [. . . ] "P" is blinking in the display. A misfeed has occurred in the paper tray or multi-bypass tray. A letter and a number appear The scan head locking switch is locked. Turn the power switch A letter and a number appear off, remove the power cord from the outlet, and contact our Technical Assistance Department at alternately. 1-(630)378-3590 in the USA or 905-568-7140 in Canada. 9 ­ 62 MISFEED REMOVAL When the misfeed ( ) indicator blinks or blinks in the display, the unit will stop because of a misfeed. If a misfeed occurs when using the SPF, a number may appear in the display after a minus sign. This indicates the number of the originals that must be returned to the document feeder tray after a misfeed. Return the required number of originals. Then this number will disappear when copying is resumed or the clear ( ) key is pressed. When the SPF misfeeds an original sheet, the unit will stop and the SPF misfeed ( ) indicator will blink, while the misfeed ( ) indicator will remain off. For a misfeed of originals in the SPF, see "D: Misfeed in the SPF" (p. 67). 1 2 Open the multi-bypass tray, and side cover, in that order. To open the multi-bypass tray, see "The multi-bypass tray" (p. 17). To open the side cover, see "INSTALLING THE TD CARTRIDGE" (p. 10). Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If the misfeed ( ) indicator blinks, proceed to "A: Misfeed in the paper feed area" (p. 64). If paper is misfed here, proceed to "B: Misfeed in the fusing area". (p. 65) If the misfed paper is seen from this side, proceed to "C: Misfeed in the transport area". (p. 66) If paper is misfed here, proceed to "A: Misfeed in the paper feed area". (p. 64) 8 63 A: Misfeed in the paper feed area 1 Gently remove the misfed paper from the paper feed area as shown in the illustration. When the misfeed ( ) indicator blinks, and the misfed paper is not seen from the paper feed area, pull out the paper tray and remove the misfed paper. If the paper cannot be removed, proceed to "B: Misfeed in the fusing area". The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so may cause a burn or other injury. · Do not touch the surface of the drum (green portion) of the drum cartridge when removing the misfed paper. [. . . ] 49 Setting the toner save mode . . . . . . . . . . . . . 54 Setting the user program. . . . . . . . . . . . . . . . . . . 55 Setting up the Button Manager. . . . . . . . . . 34 Storing the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]