User manual SHARP AL-1651CS

[. . . ] MODEL AL-1651CS AL-1661CS DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL Page PREPARATIONS LOADING PAPER MAKING COPIES CONVENIENT COPY FUNCTIONS SETTING UP THE SOFTWARE PRINTER/SCANNER FUNCTIONS USER SETTINGS 9 18 24 30 40 59 64 TROUBLESHOOTING AND MAINTENANCE 71 APPENDIX 92 AL-1651CS/AL-1661CS FOR YOUR PROTECTION. . . To aid in reporting this unit in case of loss or theft, please record below the model number and serial number located on the back of the unit. We also suggest you record all the information listed and retain for future reference. MODEL NUMBER DATE OF PURCHASE Dealer Address State Service Station Address State Zip City Telephone Zip City Telephone SERIAL NUMBER To obtain service, or to obtain product literature, accessories, or supplies, please call or 1-(630)378-3590 in the USA 905-568-7140 in Canada. For customer assistance, please visit http://www. sharpusa. com/ (for USA) or http://www. sharp. ca/ (for Canada) on the World Wide Web or call 1-(630)378-3590 (for USA). Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from copying by national law. [. . . ] Page - 16 - The machine does not operate. - 17 13 27 Copies are too dark or too light. 67 Blank copies. 24, 25 8 73 TROUBLESHOOTING AND MAINTENANCE Problem Cause and solution The original was not placed in the correct position. An appropriate ratio was not used for the size of the original and the size of the paper. Press the [COPY RATIO] key to change the ratio to a setting that is suitable for the original and the copy paper. The size of paper loaded in the tray was changed without changing the tray's paper size setting. Be sure to change the tray's paper size setting whenever you change the size of paper loaded in the tray. The paper is outside of the specified size and weight range. Use copy paper within the specified range. Wrinkles appear in the paper or the image disappears in places. During periods when the machine is not used for a long time, remove the paper from the tray and store it in a dark place in a bag to prevent moisture absorption. The document glass or the underside of the RSPF is dirty. Page 24, 25 Part of the image is cut off or there is too much blank space. 28 23 18 - Copies are smudged or dirty. 88 - 74 TROUBLESHOOTING AND MAINTENANCE Problem Cause and solution Misfeed occur. To remove the misfeed, see "MISFEED REMOVAL". The paper is outside of the specified size and weight range. Use copy paper within the specified range. During periods when the machine is not used for a long time, remove the paper from the tray and store it in a dark place in a bag to prevent moisture absorption. Make sure that the paper is properly loaded. If the stack of paper is higher than the indicator line on the tray, remove some of the paper and reload so that the stack does not exceed the line. The guides on the bypass tray do not match the width of the paper. Adjust the guides to match the width of the paper. The bypass tray extension is not pulled out. When loading a large size of paper, pull out the extension. Clean the long, narrow glass in the RSPF. [. . . ] 65, Printing Process And Printing Inks, Carbon Black and Some Nitro Compounds, Lyon, pp. 149-261 H. Muhle, B. Bellmann, O. Creutzenberg, C. Dasenbrock, H. Ernst, R. Kilpper, J. C. MacKenzie, P. Morrow, U. Mohr, S. Takenaka, and R. Mermelstein (1991) Pulmonary Response to Toner upon Chronic Inhalation Exposure in Rats. Fundamental and Applied Toxicology 17, pp. 280-299. The information on this data sheet represents our current data and best opinion as to the proper use in handling of this product under normal conditions. However, all materials may present unknown hazards and should be used with caution. [. . . ]