User manual SHARP AL-2030

[. . . ] MODEL AL-2030 AL-2040CS DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL Page INTRODUCTION SETTING UP THE UNIT LOADING PAPER INSTALLING THE SOFTWARE MAKING COPIES SPECIAL FUNCTIONS MAINTENANCE TROUBLESHOOTING THE UNIT APPENDIX 4 7 14 19 46 52 57 61 69 AL-2030 AL-2040CS FOR YOUR PROTECTION. . . To aid in reporting this unit in case of loss or theft, please record below the model number and serial number located on the back of the unit. We also suggest you record all the information listed and retain for future reference. MODEL NUMBER DATE OF PURCHASE Dealer Address State Service Station Address State Zip City Telephone Zip City Telephone SERIAL NUMBER To obtain service, or to obtain product literature, accessories, or supplies, please call 1-(630)378-3590 in the USA. For customer assistance, please visit http://www. sharpusa. com/ (for USA) on the World Wide Web or call 1-(630)378-3590 (for USA). Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations. Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from copying by national law. [. . . ] For more information on purchasing the drum cartridge, see "ABOUT SUPPLIES AND OPTIONS" (p. 71). When the indicator begins to blink, the unit will stop operating until the cartridge is replaced. Replace the drum cartridge at this time. *Based on copying onto letter size paper at 5% toned area. Do not remove the protective cover on the drum portion (black paper) of a new drum cartridge before use. The cover protects the drum against external light. 1 2 Remove the TD cartridge (see step 1 and 2 in "TD CARTRIDGE REPLACEMENT" (p. 57)). Hold the drum cartridge handle and gently pull the cartridge out. Dispose of the old drum cartridge in accordance with local regulations. Drum cartridge handle 3 Remove the new drum cartridge from the protective bag and remove the protective cover from the cartridge. Then gently install the new drum cartridge. Do not touch the surface of the drum (green portion) of the cartridge. Doing so may cause smudges on the copies. 58 4 5 Gently install the TD cartridge. To install the TD cartridge, see step 5 in "INSTALLING THE TD CARTRIDGE" (p. 11). Close the front cover and then the side cover by pressing the round projections near the side cover open button. The drum replacement required ( ) indicator will go out and the start ( indicator will light up. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged. ) CLEANING THE UNIT Proper care is essential in order to get clean, sharp copies. Be sure to take a few minutes to regularly clean the unit. Gas from the spray may come in contact with the internal electrical components or high-temperature parts of the fusing unit, creating a risk of fire or electrical shock. · Before cleaning, be sure to turn the power switch off and remove the power cord from the outlet. · Do not use thinner, benzene or other volatile cleaning agents. Doing so may cause deformation, discoloration, deterioration or malfunction. Cabinet Wipe the cabinet with a soft, clean cloth. Document glass and the back side of the SPF Stains on the document glass, SPF scanning window or SPF roller will also be copied. Wipe the document glass, SPF scanning window and SPF roller with a soft, clean cloth. If necessary, dampen the cloth with a glass cleaner. 7 Document glass/SPF scanning window SPF SPF roller SPF scanning window 59 Transfer charger If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the following procedure. 1 2 3 Turn the power switch off. [. . . ] 49 - PHOTO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Setting the copy quantity . . . . . . . . . . . . . . . . . . . 49 Setting the toner save mode . . . . . . . . . . . . . 54 Setting the user program. . . . . . . . . . . . . . . . . . . [. . . ]