User manual SHARP AR-120E

[. . . ] MODEL AR-120E DIGITAL LASER COPIER OPERATION MANUAL Page · GETTING STARTED · INSTALLATION · MAKING COPIES · SPECIAL FUNCTIONS · SUPPLIES AND USER MAINTENANCE · COPIER TROUBLE?· APPENDIX 3 8 11 17 20 24 31 CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT VAROITUS!LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. VARNING OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1. Laserstrahl R CAUTION INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. [. . . ] Use the left copy quantity ( ) key to select a user program number (1: auto clear time, 2: preheat mode, 3: auto power shut-off timer, 5: auto power shut-off mode). The selected number will blink in the left side of the display. 2 18 USER PROGRAMS 3 4 Press the print ( ) key. The entered program number will be steadily lit and the currently selected parameter number for the program will blink on the right side of the display. Select the desired parameter using the right copy quantity ( parameter number will blink on the right of the display. 1 2 3 5 Mode Auto clear time Preheat mode Auto power shutoff timer Auto power shutoff mode 0 3 0 0 3 0 OFF 90 sec. 4 OFF *1 Factory default settings are indicated with an asterisk (*). 4 Special functions 5 Press the print ( ) key. The right-hand number in the display will be steadily lit and the entered value will be stored. To change the setting or to set another mode, press the clear ( copier will return to step 2. ) key. The 6 Press the light ( ) or dark ( ) key to return to the normal copy mode. 19 5 q SUPPLIES AND USER MAINTENANCE This chapter describes how to replace the TD cartridge and the drum cartridge and how to check the total number of copies. Be sure to use only genuine SHARP parts and supplies. TD CARTRIDGE REPLACEMENT The toner required ( ) indicator will light up when toner is needed. If copying is continued while the indicator is lit, copies will gradually become lighter until the copier stops and the indicator begins blinking. Replace the old TD cartridge by following the procedure given below. After the copier stops, it may be possible to make a few more copies by taking the TD cartridge out of the copier, shaking it horizontally, then reinstalling it. If copying is not possible after this operation, replace the TD cartridge. q During long copy run of a dark original, the ready ( ) indicator may blink, the indicator light up, and the copier stop, even though toner is left. The copier will feed toner up to 2 minutes and then the ready ( ) indicator will light up. Press the print ( ) key to restart copying. Open the side cover while pressing the side cover open button. Then, push gently on both sides of the front cover to open the cover. 5 Supplies and user maintenance 1 2 Gently pull the TD cartridge out while pressing the lock release button. Dispose of the old TD cartridge in accordance with local regulations. Lock release button 20 TD CARTRIDGE REPLACEMENT 3 Remove the TD cartridge from the bag. Hold the cartridge on both sides and shake it horizontally four or five times. Hold the tab of the protective cover and pull the tab to remove the cover. 4 or 5 times 4 Gently insert the TD cartridge until it locks in place. 5 Supplies and user maintenance 5 Close the front cover and then the side cover by pressing the round projections near the side cover open button. The indicator will go out and the ready ( ) indicator will light up. [. . . ] 3 mm (1/8") (either of the other edges) AR-120E: 12 copies/min. (normal copying mode) Variable: 50% to 200% in 1% increments (total 151 steps) Fixed: 50%, 70%, 81%, 100%, 141%, 200% (50%, 64%, 78%, 100%, 129%, 200%) Moving optical source, slit exposure (stationary platen) with automatic exposure One paper tray with automatic feed (250 sheets); one single-sheet manual bypass Heat rollers Magnetic brush development Xenon lamp Scan: 400 dpi Output: 600 dpi AR-120E: N/A AR-150E: 6MB 240V +6%, -10% in 240V power supply regions or local voltage ±10% in other regions (For this copier's power supply requirements, see the name plate located on the back of the unit. ) Max. 1, 000 W 607 mm (W) x 445 mm (D) (23. 9" (W) x 17. 5" (D)) Approx. 18 kg (39. 7 lbs. ), TD and drum cartridges included 518 mm (W) x 445 mm (D) x 293 mm (H) (20. 4" (W) x 17. 5" (D) x 11. 5" (H)) Temperature: 10°C to 30°C (50°F to 86°F) Humidity: 20% to 85% Sound Power Level LWA Copying: 66 [dB (A)], Standby: Background noise level Sound Pressure Level LPA (bystander positions) Copying: 40 [dB (A)], Standby: Background noise level Noise emission measurement in accordance with ISO 7779. SPECIFICATIONS Continuous copying First-copy time (Approx. ) Copy ratio Exposure system Copy paper feed Fusing system Development system Light source Resolution Memory Power supply 7 Appendix Power consumption Overall dimensions Weight Copier dimensions Operating conditions Noise level First-copy time may differ depending on operating conditions, such as power-supply voltage and room temperature. q q As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. [. . . ]