User manual SHARP AR-121E/151E

[. . . ] MODEL AR-121E AR-151E DIGITAL LASER COPIER OPERATION MANUAL Page · GETTING STARTED · INSTALLATION · MAKING COPIES · SPECIAL FUNCTIONS · SUPPLIES AND USER MAINTENANCE · COPIER TROUBLE?· APPENDIX 3 8 11 17 20 25 32 cover-1_AR121151EX. p65 2 30/11/00, 19:07 CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT VAROITUS!LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. VARNING OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1. Laserstrahl R CAUTION INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. [. . . ] The total number of copies will appear in two steps, each with three digits. Example: Total number of copies is 1, 234. 19 chap-4_AR121151EX. p65 19 30/11/00, 19:08 5 SUPPLIES AND USER MAINTENANCE Be sure to use only genuine SHARP parts and supplies. This chapter describes how to replace the toner cartridge. TONER CARTRIDGE REPLACEMENT When the toner cartridge replacement required ( ) indicator lights up, replacement of the toner cartridge will be needed soon. When the toner cartridge replacement required ( ) indicator blinks, the toner cartridge must be replaced before copying can be resumed. Replace the toner cartridge by following the procedure below. During a long copy run of a dark original, the ready ( ) indicator may blink, the indicator light up, and the copier stop, even though toner is left. The copier will feed toner up to 2 minutes and then the ready ( ) indicator will light up. Press the print ( ) key to restart copying. Open the side cover while pressing the side cover open button. Then, push gently on both sides of the front cover and open it. 5 Supplies and user maintenance 1 2 Push the toner cartridge lock release lever and pull the toner cartridge out. Dispose of the old toner cartridge in accordance with local regulations. Toner cartridge lock release lever After removing the toner cartridge, do not shake it or tap on it. Doing so may cause toner to leak from the cartridge. Put the old cartridge immediately in the bag contained in the box of the new cartridge. 20 chap-5_AR121151EX. p65 20 30/11/00, 19:08 TONER CARTRIDGE REPLACEMENT 3 Remove the toner cartridge from the bag. Grasp the cartridge on both sides and shake it horizontally four or five times. After shaking the cartridge, remove the toner seal. Grasp the toner cartridge as shown in the illustration. Do not hold the cartridge by the shutter. Be sure to only shake the cartridge before the toner seal is removed. 4 or 5 times Shutter Toner seal 4 Gently insert the toner cartridge along the guides until it locks in place while pushing the lock release lever. Pull the shutter out of the toner cartridge as shown in the illustration. Discard the shutter. 5 Supplies and user maintenance 5 Close the front cover and then the side cover by pressing the round projections near the side cover open button. The indicator will go out and the ready ( ) indicator will light up. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged. [. . . ] 1, 000 W 607 mm (W) x 445 mm (D) (23. 9" (W) x 17. 5" (D)) Approx. 18 kg (39. 7 lbs. ), toner cartridge included 518 mm (W) x 445 mm (D) x 293 mm (H) (20. 4" (W) x 17. 5" (D) x 11. 5" (H)) Temperature: 10°C to 30°C (50°F to 86°F) Humidity: 20% to 85% Sound Power Level LWA Copying: 66 [dB (A)], Standby: Background noise level Sound Pressure Level LPA (bystander positions) Copying: 40 [dB (A)], Standby: Background noise level Noise emission measurement in accordance with ISO 7779. SPECIFICATIONS Continuous copying First-copy time (Approx. ) Copy ratio Exposure system Copy paper feed Fusing system Development system Light source Resolution Memory Power supply 7 Appendix Power consumption Overall dimensions Weight Copier dimensions Operating conditions Noise level First-copy time may differ depending on operating conditions, such as power-supply voltage and room temperature. G G As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. [. . . ]