User manual SHARP AR-156

[. . . ] MODEL AR-156 DIGITAL LASER COPIER OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · SPECIAL FUNCTIONS · SUPPLIES AND USER MAINTENANCE · COPIER TROUBLE?· APPENDIX · OPTIONAL EQUIPMENT 3 12 20 23 27 36 40 00cover1-156ex. p65 1 4/11/00, 9:34 CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT VAROITUS!LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. VARNING OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1. Caution This product contains a low power laser device. [. . . ] In this case, open and close the side cover. The copier will feed toner again approximately 2 minutes and then copying can be restarted. 24 00C-4-156ex. p65 24 21/11/00, 16:23 TONER CARTRIDGE REPLACEMENT Toner cartridge life To find out the approximate quantity of toner remaining, follow the procedure below. Press and hold down the light ( ) and dark ( , , ) keys simultaneously for more than and ) blink and "­ ­" appears in 5 seconds until all the alarm indicators ( the display. Press and hold down the copy ratio display ( ) key for more than 5 seconds. G The approximate quantity of toner remaining will be indicated in the display as a percentage. ("100" , "75" , "50" , "25" , or "10" is displayed. ) When the percentage is less than 10%, will be displayed. G All the alarm indicators will go out. 4 Supplies and user maintenance USER MAINTENANCE Proper care is essential in order to get clean, sharp copies. Be sure to take a few minutes to regularly clean the copier. Before cleaning, be sure to turn the power switch off and remove the power cord from the outlet. Do not use thinner, benzene or other volatile cleaning agents. Doing so may cause deformation, discoloration, deterioration or malfunction. Cabinet Wipe the cabinet with a soft, clean cloth. Original table and original cover Stains on the glass, cover or RSPF roller will also be copied. Wipe the glass, cover and RSPF roller with a soft, clean cloth. If necessary, dampen the cloth with a glass cleaner. Original table Original cover RSPF roller 25 00C-4-156ex. p65 25 4/11/00, 9:38 Transfer charger If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the following procedure. Ensure that the bypass tray is open and then open the side cover while pressing the side cover open button. Take the charger cleaner out by holding the tab. Set the charger cleaner onto the right end of the transfer charger, gently slide the cleaner to the left end, and then remove it. Repeat this operation two or three times. Slide the charger cleaner from the right end to the left end along the groove of the transfer charger. If the cleaner is stopped on the way, smudges on copies may occur. 4 Supplies and user maintenance Return the charger cleaner to its original position. Close the side cover by pressing the round projections near the side cover open button. Turn the power switch on. When copier is not in use To prevent entry of dust and foreign matter, store the copier as follows. Remove the power cord and secure the copier using tape (four locations). 26 00C-4-156ex. p65 26 4/11/00, 9:38 COPIER TROUBLE? This chapter describes misfeed removal and troubleshooting. MISFEED REMOVAL When the misfeed ( ) indicator blinks or blinks in the display, the copier will stop because of a misfeed. If a misfeed occurs when using the RSPF, a number may appear in the display after a minus sign. This indicates the number of the originals that must be returned to the document feeder tray after a misfeed. [. . . ] Carcinogenicity: In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible human carcinogen). This classification is given to chemicals for which there is inadequate human evidence, but sufficient animal evidence on which to base an opinion of carcinogenicity. The classification is based upon the development of lung tumors in rats receiving chronic inhalation exposures to free carbon black at levels that induce particle overload of the lung. Studies performed in animal models other than rats did not show any association between carbon black and lung tumors. [. . . ]