User manual SHARP AR-163

[. . . ] MODEL AR-163 DIGITAL LASER COPIER OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · STATUS INDICATORS · GENERAL INFORMATION · OPTIONAL EQUIPMENT 2 13 28 35 53 CAUTIONS Follow the cautions below when using this copier. G G The fusing area is hot. Exercise care in this area when removing misfed paper. Do not look directly at the light source. Doing so may damage your eyes. G G G Place the copier on a firm, level surface. [. . . ] For programs 10 to 15 (programs for auditing accounts), the display varies with the program number. See page 38 for setting programs 10 to 15. G 36 USER PROGRAMS 4 Select the desired parameter using the numeric keys. G The entered parameter number will blink on the right side of the copy quantity display. The parameters are shown in the table below. For example, to change the setting of the auto power shut-off timer to 60 min. , press key 2. G Program name Auto clear time Parameters 0 OFF 1 30 sec. Stream feeding mode *0 OFF 1 ON Auto power shut-off setting 0 OFF *1 ON Border line for 2 in 1 or 4 in 1 * 0 OFF 1 ON Rotation copy 0 OFF *1 ON Auto paper select mode 0 OFF *1 ON Auto tray switching 0 OFF *1 ON Erase width adjustment 0 0 mm 1 5 mm (0 0" 1 1/4" Layout in 2 in 1 copy *1 Pattern 1 2 Pattern 2 Layout in 4 in 1 copy *1 Pattern 1 2 Pattern 2 Offset of paper output tray 0 Upper OFF, lower OFF 2 Upper ON, lower OFF G *2 2 3 60 sec. 240 min. *2 *2 3 *1 3 10 mm 1/2" 3 3 15 mm 3/4" 4 4 20 mm 1") Pattern 3 4 Pattern 4 Upper ON, lower ON Upper OFF, lower ON GENERAL INFORMATION Factory default settings are indicated with an asterisk (*). For layout in 2 in 1 copy and 4 in 1 copy, see page 61. ** In European countries, the default setting of the preheat mode is 1 ( 30 sec. ). For other programs, factory default settings in these countries are same to those shown above with an asterisk (*). If you select "0" (OFF) in a program, the corresponding function will be disabled. 5 Press the START ( G ) key. The right-hand number in the copy quantity display will be steadily lit and the entered value will be stored. User programs 6 To continue with other user programs, press the key and then repeat steps 2 to 5. To exit the user program mode, press the light ( ) key. G All the alarm indicators will go out. 37 USER PROGRAMS Settings for auditing accounts Settings of user programs No. 10 to 15 varies with the program number. For setting of all programs, first follow steps 1 to 3 in "Setting the user programs" on page 36 to select a program. Press the light ( ) key for more than 5 seconds. Enter a program number (10 to 15) using the numeric keys. Press the START ( ) key. ) Then follow the appropriate instructions for the program. Program No. 10: Auditing mode If the auditing mode is enabled, copying is limited to operators with an assigned 3-digit account number. A maximum of 20, 3-digit account numbers can be assigned. 10 is entered, the current setting (0: OFF, 1:ON) will blink on the right side of the copy quantity display. 1. Select the desired setting using the numeric keys. 0: 1: OFF ON 2. Press the START ( G ) key. The setting will be stored. 3. To continue with other user programs, press the key and enter another program number. To exit the user program mode, press the light ( ) key. GENERAL INFORMATION Program No. 11 is entered, "­ ­ ­" will blink in the copy quantity display. G If the number of accounts has reached the upper limit (20), "11E" will appear in the copy quantity display. [. . . ] This classification is given to chemicals for which there is inadequate human evidence, but sufficient animal evidence on which to base an opinion of carcinogenicity. The classification is based upon the development of lung tumors in rats receiving chronic inhalation exposures to free carbon black at levels that induce particle overload of the lung. Studies performed in animal models other than rats did not show any association between carbon black and lung tumors. While there have been no studies to date using developer, a two-year cancer bioassay using a typical toner preparation containing carbon black (a small amount of toner is included in the developer mixture) demonstrated no association between toner exposure and tumor development in rats. [. . . ]