User manual SHARP AR-206

[. . . ] MODEL AR-206 DIGITAL LASER COPIER OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · STATUS INDICATORS · GENERAL INFORMATION · OPTIONAL EQUIPMENT 2 13 28 36 55 CAUTIONS Follow the cautions below when using this copier. G G The fusing area is hot. Exercise care in this area when removing misfed paper. Do not look directly at the light source. Doing so may damage your eyes. G G G Place the copier on a firm, level surface. [. . . ] For example, to change the setting of the auto power shut-off timer to 60 min. , press key 2. G Program name Auto clear time Parameters 0 OFF 1 30 sec. Stream feeding mode *0 OFF 1 ON Auto power shut-off setting 0 OFF *1 ON Border line for 2 in 1 or 4 in 1 * 0 OFF 1 ON Rotation copy 0 OFF *1 ON Auto paper select mode 0 OFF *1 ON Auto tray switching 0 OFF *1 ON Erase width adjustment 0 0 mm 1 5 mm Layout in 2 in 1 copy *1 Pattern 1 2 Pattern 2 Layout in 4 in 1 copy *1 Pattern 1 2 Pattern 2 Offset of paper output tray 0 Upper OFF, lower OFF Upper ON, lower OFF 2 Image rotation in duplex *0 OFF 1 ON copying Location of the margin *1 Left 2 Top *2 2 3 60 sec. 240 min. *2 3 *1 3 10 mm 3 15 mm 4 20 mm Pattern 3 4 Pattern 4 Upper ON, lower ON Upper OFF, lower ON GENERAL INFORMATION Factory default settings are indicated with an asterisk (*). For layout in 2 in 1 copy and 4 in 1 copy, see page 67. If you select "0" (OFF) in a program, the corresponding function will be disabled. 5 Press the START key. G The right-hand number in the copy quantity display will be steadily lit and the entered value will be stored. User programs 6 To continue with other user programs, press the key and then repeat steps 2 to 5. To exit the user program mode, press the light ( ) key. G All the alarm indicators will go out. 38 USER PROGRAMS Settings for auditing accounts Setting of user programs No. 10 to 15 varies with the program number. For settings of all programs, first follow steps 1 to 3 in "Setting the user programs" on page 37 to select a program. Press the light ( ) key for more than 5 seconds. Enter a program number (10 to 15) using the numeric keys. Press the START key. ) Then follow the appropriate instructions for the program. Program No. 10: Auditing mode If the auditing mode is enabled, copying is limited to operators with an assigned 3-digit account number. A maximum of 20, 3-digit account numbers can be assigned. 10 is entered, the current setting (0: OFF, 1:ON) will blink on the right side of the copy quantity display. 1. Select the desired setting using the numeric keys. 0: 1: OFF ON 2. Press the START key. G The setting will be stored. 3. To continue with other user programs, press the key and enter another program number. To exit the user program mode, press the light ( ) key. GENERAL INFORMATION Program No. 11 is entered, "­­­" will blink in the copy quantity display. G If the number of accounts has reached the upper limit (20), "11E" will appear in the copy quantity display. The copier will return to step 2 on page 37. User programs 1. Enter a 3-digit account number using the numeric keys. G Any 3-digit number except "000" can be registered as an account number. 2. Press the START key. G If a number that is already registered or "000" is entered, the number will blink in the copy quantity display. 3. 4. Repeat steps 1 and 2 for other account numbers. To continue with other user programs, press the key and enter another program number. To exit the user program mode, press the light ( ) key. 39 USER PROGRAMS Program No. 12 is entered, an account number will appear in the copy quantity display. [. . . ] None None Flash Point (Method Used): Ignition Temperature: Flammable Limits: Extinguishing Media: Special Fire Fighting Procedure: Unusual Fire and Explosion Hazard: Sensitivity to Mechanical Impact: Sensitivity to Static Charge: Section 8. Reactivity Data Stable None CO and NOx Will not occur. Stability: Incompatibility (Material to Avoid): Hazardous Decomposition: Hazardous Polymerization: Section 9. Precautions for Safe Handling and Use Personal Protection Information (Respiratory, Eye Protection and Protective Glove): None required under normal use. Engineering Control / Ventilation: Not required. Steps to be taken in case of Spill or Leak: Sweep up or clean up with vacuum cleaner. Waste Disposal Method: Waste material may be dumped or incinerated under conditions which meet all federal, state and local environmental regulations. Section 10. [. . . ]