User manual SHARP AR-275

[. . . ] MODEL AR-235 AR-275 DIGITAL LASER COPIER/PRINTER OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · SPECIAL FUNCTIONS · COPIER TROUBLE? 5 23 41 65 · GENERAL INFORMATION 77 · OPTIONAL EQUIPMENT 91 · KEY OPERATOR'S GUIDE 117 In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF". The symbol " " denotes the copier is not completely de-energized but in a stand-by condition at this "POWER" switch position. If your copier is so marked, please read "I" for "ON" and " " for "OFF". For a complete electrical disconnection, pull out the main plug. [. . . ] The package of SHARP toner has the Genuine Supplies label. GENUINE SUPPLIES 1 Gently open the front cover. 2 GENERAL INFORMATION Push the toner cartridge lock release lever and pull the toner cartridge out. Remove the toner cartridge while supporting it with the left hand at the green label portion. Toner cartridge lock release lever Grip q For disposal of the old toner cartridge, contact your dealer. NOTE: After removing the toner cartridge, do not shake it or tap on it. Doing so may cause toner to leak from the cartridge. Put the old cartridge immediately in the bag contained in the box of the new cartridge. 82 TONER CARTRIDGE REPLACEMENT 3 Remove the new toner cartridge from the bag. Grasp the cartridge on both sides and shake it horizontally approximately 20 times. After shaking the cartridge, remove the tape. NOTE: Grasp the grip when holding the cartridge. Do not hold the cartridge by the shutter. Be sure to only shake the cartridge before the tape is removed. Approx. 20 times Shutter Tape 4 Gently insert the toner cartridge along the guides until it clicks in place while pushing the lock release lever. NOTE: If dirt or dust is adhered to the toner cartridge, remove it before installing the cartridge. 5 Remove the tape from the shutter. Pull the shutter out of the toner cartridge as shown in the illustration. Discard the shutter. 5 GENERAL INFORMATION 6 Close the front cover. 83 CHECKING THE TONER QUANTITY AND TOTAL OUTPUT COUNT The approximate quantity of toner remaining and the total output count can be displayed by the procedure below. The total count value displayed is the output count in the copy, print, and fax modes including the output count by the self-print function of the printer and facsimile features. 1 Press and hold the COPY key during standby or warm-up. TOTAL OUTPUT 26, 788 TONER REMAINING(%) 0 25 50 75 100 q The toner quantity and the total output count will be displayed in the message display while the key is pressed. NOTE: An A3 or 11" x 17" sheet is counted as two sheets. A two-sided copy is also counted as two sheets. GENERAL INFORMATION 84 CLEANING THE PLATEN GLASS AND PLATEN COVER Proper care is essential for clean, sharp copies. Please take a few minutes to regularly clean your copier. Stains or dirt on the platen glass or platen cover will also be copied. Wipe the platen glass and platen cover with a soft, clean cloth. q If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents. q If an optional SPF or RSPF is installed, wipe the platen cover portion of the SPF or RSPF and the scanning window on the platen glass. 5 GENERAL INFORMATION 85 CLEANING THE BYPASS TRAY PAPER FEED ROLLER If misfeeds occur frequently when feeding postcards, envelopes, thick paper, etc. through the bypass tray, wipe the paper feed roller at the feed slot of the bypass tray with a soft, clean cloth dampened with alcohol or water. Paper feed roller GENERAL INFORMATION 86 DISPLAY CONTRAST ADJUSTMENT The contrast of the display can be adjusted as below. 1 Press the SPECIAL FUNCTION key. q The SPECIAL FUNCTION screen will appear. SPECIAL FUNCTION SPECIAL MODES ORIG. SIZE ENTER PAPER SIZE SET DISPLAY CONTRAST 2 Use the OK key. q The and keys to select "DISPLAY CONTRAST" and press the screen for contrast setting will appear. DISPLAY CONTRAST 3 Use the and keys to adjust the contrast. 5 GENERAL INFORMATION q To reset the contrast to the default setting, press the CLEAR (C) key. 4 Press the SPECIAL FUNCTION key. q The display will return to the basic screen. 87 STORAGE OF SUPPLIES Standard supplies for this copier that are to be replaced by the user are copy paper, toner cartridge, and staple cartridge for the optional finisher (AR-FN5). For best copying results, be sure to use only SHARP products. Only genuine SHARP consumables carry the Genuine Supplies label. GENUINE SUPPLIES Proper storage 1 2 Store the supplies in a location that is: q clean q at and dry, a stable temperature, q not exposed to direct sunlight. Store copy paper in the wrapper and lying flat. q Paper stored in packages standing up or out of the wrapper may curl or become damp, resulting in paper misfeeds. GENERAL INFORMATION 88 SPECIFICATIONS AR-235 Type Copy system Originals Original sizes Copy sizes Digital laser copier/printer, desktop Dry, electrostatic transfer Sheets, bound documents Max. A6 (5-1/2" x 8-1/2") Image loss: Max. 4 mm ( 5/32") (leading and trailing edges), Max. [. . . ] TRANSPORT INFORMATION UN Classification Land DOT (USA) IMDG Sea ICAO-TI Air : : : : None None None None 150 15. REGULATORY INFORMATION US Information TSCA (Toxic Substances Control Act): All chemical substances in this product comply with all applicable rules or order under TSCA. SARA (Superfund Amendments and Reauthorization Act) Title III 302 Extreme Hazardous Substance : None 311/312 Hazard Classification : None EU Information 1999/45/EC and 67/548/EEC Symbol & Indication : Not required R-Phrase : Not required 76/769/EEC : All chemical substances in this product comply with all applicable rules or order under 76/769/EEC. 16. OTHER INFORMATION NFPA Rating (USA) : Health=1 Flammability=1 Reactivity=0 WHMIS Legislation (Canada) : This product is not a controlled product. [. . . ]