User manual SHARP AR-5015N/5020

[. . . ] MODEL AR-5015 N AR-5020 DIGITAL LASER COPIER OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · STATUS INDICATORS · GENERAL INFORMATION · OPTIONAL EQUIPMENT 2 13 28 35 53 CAUTIONS Follow the cautions below when using this copier. G G The fusing area is hot. Exercise care in this area when removing misfed paper. Do not look directly at the light source. Doing so may damage your eyes. G G G Place the copier on a firm, level surface. [. . . ] Pull the shutter out of the toner cartridge as shown in the illustration. Close the front cover by pushing both sides with your hands and then close the side cover by pressing the handle on the cover. The indicator will go out. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged. Even after a new toner cartridge is installed, the START key ( ) indicator may not light up, indicating copying cannot be restarted (toner is not sufficiently fed). In this case, open and close the side cover. The copier will feed toner again approximately 2 minutes and then copying can be restarted. STATUS INDICATORS Toner cartridge replacement Toner cartridge life To find out the approximate quantity of toner remaining, follow the procedure below. 1 2 3 Press and hold the light ( ) key for more than 5 seconds until all the alarm indicators ( , , , , and ) blink and "­­" appears in the copy quantity display. Press and hold the copy ratio display ( than 5 seconds. G ) key for more The approximate quantity of toner remaining will be indicated in the copy quantity display as a percentage. ( "100", "75", "50", "25", or "10" is displayed. ) When the percentage is less than 10%, "LO" will be displayed. Press the light ( G ) key. All the alarm indicators will go out. 29 MISFEED REMOVAL The copier will stop when a misfeed occurs. The misfeed ( ) indicator will blink, and blinking red misfeed location indicators will indicate the approximate misfeed location. If paper is accidentally torn during removal, be sure to remove all pieces. Be careful not to damage the photoconductive drum. For misfeeds in optional equipment, see its section of the operation manual. First confirm the misfeed location. ( ( P. 30, 33) STATUS INDICATORS Misfeed in the bypass tray 1 2 Gently pull the misfed paper out. Misfeed removal Lift slightly on the side cover and slide the cover out until it stops. Close the side cover by pressing the handle on the cover. G The misfeed ( ) indicator will go out. Misfeed in the copier 1 30 Open the bypass tray. Lift slightly on the side cover and slide the cover out until it stops. MISFEED REMOVAL 2 If the misfed paper is seen from this side, proceed to C. Misfeed in the transport area . Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If paper is misfed here, proceed to B. Misfeed in the fusing area . If paper is misfed here, proceed to A. Misfeed in the paper feed area . A. Misfeed in the paper feed area Push gently on both sides of the front cover and open it. 1 2 STATUS INDICATORS Roller rotating knob Carefully remove the misfed paper. Turn the roller rotating knob in the direction of the arrow to assist in removing it. The fusing unit is hot. Take care in removing paper. Misfeed removal Do not touch the photoconductive drum (green portion) when removing the misfed paper. [. . . ] While this indicator is blinking, any new originals placed in the SPF will be fed and copied automatically. See page 35, USER PROGRAMS. 1 2 3 4 Ensure that no original is left on the original table. Adjust the original guides to the size of the originals. Single pass feeder (AR-SP2) Set the originals face up in the document feeder tray. G The SPF indicator will light up. If this indicator does not light up, the originals are not properly set or the SPF is not properly closed. Ensure that the copy paper size in the paper tray is the same size as the originals. OPTIONAL EQUIPMENT 5 Set the number of copies (AR-5020 only) and press the START ( ) key. G G With AR-5015 N, only one copy per original can be made. The AR-5020 copier is equipped with a 1-page memory buffer. [. . . ]