User manual SHARP AR-5316/5320/5316X/5320X

[. . . ] MODEL AR-5316 AR-5320 AR-5316 X AR-5320 X DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL Page AR-5316/AR-5316 X · BEFORE USING THE MACHINE · COPY FUNCTIONS · PRINTER FUNCTIONS · USER SETTINGS · TROUBLESHOOTING · ROUTINE MAINTENANCE · PERIPHERAL DEVICES AND SUPPLIES · APPENDIX 8 18 29 31 40 55 58 60 AR-5320/AR-5320 X Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from copying by national law. Other items may be prohibited by local law. G Money G Checks G Stamps G Passports G Bonds G Stocks G Bank drafts G Driver's licenses In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF". [. . . ] To cancel a print job, press the [CLEAR] key ( ) or the [CLEAR ALL] key ( ). To resume printing, press the [ON LINE] key ( ) to switch the machine online. When "Use close paper size" is disabled The PAPER SIZE indicator on the operation panel will blink. You can press the [TRAY SELECT] key ( tray manually, or load paper in the bypass tray and press the [ON LINE] key ( ) to begin printing. ) to select a When "Use close paper size" is enabled Printing will take place using a size of paper that is close to the size of the print image. OPERATION IN COPY AND PRINTER MODES Some operations cannot be performed simultaneously when the machine is being used in printer mode or copy mode. Modes Copy Printer Copy key input During copying During printing Copying Yes Yes*1 Yes*3 Printing Yes No*2 No *1 Can be used after pressing the [INTERRUPT] key ( ). *2 Printing will begin when the [CLEAR ALL] key ( ) is pressed after the copy job is finished, or when the [ON LINE] key ( ) is pressed to switch the machine online. Printing will also begin after the set auto clear time elapses, or after 60 seconds if "Auto clear time" is disabled. *3 The print job is paused and copying begins. 30 4 Note Chapter 4 USER SETTINGS This chapter explains how to set the automatic exposure level, toner save mode/high image quality mode, and the user programs, which are custom settings that control fine points of the machine's operation. ADJUSTING THE AUTOMATIC EXPOSURE LEVEL The exposure level used in automatic exposure adjustment, which automatically adjusts the copy exposure according to the original, can be adjusted. If copies tend to be too dark or too light when automatic exposure adjustment is used, follow the steps below to adjust the automatic exposure level. The automatic exposure level can be adjusted separately for the document glass and the SPF. The copy and printer cannot be used while the automatic exposure level is being adjusted. 1 To adjust the automatic exposure level in the SPF, place the original in the SPF. (p. 19) Make sure that the SPF indicator is lit. To adjust the automatic exposure level for copies made from originals placed on the document glass, proceed to step 2. 4 Press the [Light] key ( ) or [Dark] key ( ) to lighten or darken the automatic exposure level as desired. 135 Note 2 3 Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to select "PHOTO" ( ). Hold down the [AUTO/TEXT/PHOTO] key ( AUTO / / ) until the AUTO indicator ( AUTO ) blinks. AUTO 5 Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to complete the setting. The AUTO indicator ( AUTO ) stops blinking and lights steadily. 135 The exposure level indicators show the current setting. Note After adjusting the automatic exposure level, it is recommended that you make a test copy to check the new level. 31 TONER SAVE MODE AND HIGH IMAGE QUALITY MODE Toner save mode can be enabled to reduce toner consumption by about 10%. The high image quality mode improves copy image quality in the automatic and manual exposure modes by increasing copy density with a slight increase of toner consumption. To switch between toner save mode and high image quality mode, follow the steps below. Note In Europe, high image quality mode is initially selected. In regions other than Europe, toner save mode is initially selected. 1 Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to select "TEXT" ( ). Hold down the [AUTO/TEXT/PHOTO] key ( AUTO / / ) until the PHOTO indicator ( ) blinks. AUTO 2 135 The exposure level indicators show the current setting. 3 To enable toner save mode, press the [Light] key ( ). To enable high image quality mode, press the [Dark] key ( ). 135 When enabling toner save mode, make sure that "1" is lit. When enabling high image quality mode, make sure that "5" is lit. 4 Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to complete the setting. The PHOTO indicator ( lights steadily. ) stops blinking and 32 CUSTOMISING SETTINGS (User programs) The user programs allow you to customise the machine to match your needs. USER PROGRAMS Program number Program name Setting codes (factory default setting appears in bold) 1: OFF 2: 10 sec. Explanation · "Auto clear time" automatically returns the copy settings to the initial settings (p. 12) when a certain period of time elapses after a copy is made. This program is used to select the period of time. "Auto clear time" can also be disabled. [. . . ] 10, 23, 24 65 INDEX BY PURPOSE Copying Automatic ratio selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Cancelling a copy run. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 19 Copying, starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 19 Dual page copying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Enlargement/reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Exposure adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Exposure selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]