User manual SHARP AR-650

[. . . ] Model Number Serial Number Date of Purchase Place of Purchase Authorized Sharp Copier Service Department Number FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. [. . . ] The display on the control panel returns to the default modes. Tip: The copier returns to the default copy modes after 45 seconds even if the ALL CLEAR key is not pressed. ALL CLEAR 1 4 7 0 2 5 8 C CLEAR 3 STOP 6 9 START 54 USING THE EDITING FUNCTIONS USING THE EDITING FUNCTIONS 55 1. IMAGE SHIFT COPYING You can create margins on the copy, and you can specify the position of these margins on either the right or the left side of the copy. You can also create margins on copies of book originals with just the use of the DUAL PAGE mode. The default margin is approximately 7 mm, but you can select any margin between 0 and 30 mm. Example of Image Shift Copying Margin on left side Copy Margin on right side Copy Normal binding : left or right Procedure 1 2 3 Press the EDIT key to enter the Editing menu. . The menu on the right appears. Press the IMAGE SHIFT key to select the image shift function in the Editing menu. Select on which side the margin is to be created. . Press one of LEFT , RIGHT or BOOK to select the type of margin. If you select the BOOK margin, use it in conjunction with the DUAL PAGE mode. 56 4 Press the SET key. . To change the margin: Press the 0mm or 30mm key to select the desired margin setting, and press the SET key. When combining image shifting with duplex copying, select FRONT for the front side and BACK for the back side of the copy. 5 6 7 Place the originals on the original feed tray or on the glass. . After aligning the edges of the originals, set them face up on the original feed tray and align the slides to the edges of the originals. The menu on the right appears. Press the DUAL PAGE key to select the dual-page copy function. Select 1 SIDE (single-sided) copying or 2 SIDE (two-sided) copying. Select the Letter copy size. Place the original on the glass. . Align the center of the original to the yellow indicator with its bottom toward you. Select the desired exposure, copy quantity, reproduction ratio, etc. as required. B O OK Press the START key. Yellow indicator line 60 4. X-Y ZOOM This function allows you to make copies of originals with the reproduction ratio of the X and Y directions changed. Example of X-Y zoom 100% When the Y zoom ratio is changed When the X zoom ratio is changed 200% USING THE EDITING FUNCTIONS 100% 200% Procedure 1 Select the X-Y zoom function in the Editing menu. . Press the EDIT key to enter the Editing menu, and then press the XY ZOOM key. The menu on the right appears. 2 3 4 5 Specify the X and Y reproduction ratios. . Press the 25%< or >400% key to select the X and Y reproduction ratios, and press the upper SET key. Press the lower SET key. Select the desired copy size, exposure and copy quantity. Place the original on the glass or the automatic document feeder and press the START key. 61 5. TRIMMING/MASKING This function allows you to trim or mask copies. You can trim originals (inside area only) by selecting the trimming mode, and you can mask originals (outside area only) by selecting the masking mode. [. . . ] SIMPLE TROUBLESHOOTING (1) Copier does not start Is the power cord plug firmly inserted No in the outlet? Insert the power cord plug firmly. Y e s Is the front cover No firmly closed? Close the front cover properly. Has the digital copier started?N o Is the exit guide firmly closed? No Close the exit cover properly. Call for service. MAINTENANCE 169 2. SIMPLE TROUBLESHOOTING (2) Copies are not clear Is the transport belt Yes or the glass dirty? Clean the transport belt and the glass with a dry cloth or alcohol. Y e s Are images in the original reproduced clearly? [. . . ]