User manual SHARP AR-C360P

[. . . ] 2 Copyright Copyright Sharp AR-C360P EFI User's Software Installation Guide P/N 59379501, Revision 1. 1 September, 2005 Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Sharp assumes no responsibility for the results of errors beyond its control. Sharp also cannot guarantee that changes in software and equipment made by other manufacturers and referred to in this guide will not affect the applicability of the information in it. Mention of software products manufactured by other companies does not necessarily constitute endorsement by Sharp. [. . . ] This is not necessary in the PCL driver. Click OK to activate the current settings. You are ready to connect to your network type (see the next section "Completing the Windows 2000/XP/Server 2003 printer connection"). Configuring installed options and updating print options Sharp AR-C360P EFI User's Software Installation Guide - 47 1 1-48 Installing User Software on a Windows Computer settings automatically If you have a TCP/IP-enabled network, you can automatically update your printer driver to reflect the options currently installed on the Fiery. When the printer driver is first installed, the installable options have default settings that were set up in Fiery Setup or ColorWise Pro Tools. When you update the printer driver with the Two-Way Communication feature, you allow the Fiery to complete the actual setting. The Two-Way Communication feature also updates Expert Color Settings options to reflect the current Color settings on the Fiery. To access the Expert Color Settings options, click the Expert Settings tab in the ColorWise print option bar of the Fiery printing tab of your printer driver. For more information, see Chapter 1 of the Color Guide. To set up Two-Way Communication for PostScript or PCL printer drivers for Windows 2000/XP/Server 2003 1. In the Installable Options (PS) or Device Options (PCL) tab, select TwoWay Communication. Type the Sharp AR-C360P's IP address or DNS name. In the PS driver, to display the Sharp AR-C360P's current default settings when opened, select Update Fiery Driver When Opened. In the PS driver, to receive an e-mail notification after your job has been printed, select Enable E-mail Notification, and type in the e-mail address to which notification should be sent. You will also receive e-mail notification of any errors that occur during printing. Note: Enable E-mail Notification is displayed only if Email Service is enabled at Setup. Sharp AR-C360P EFI User's Software Installation Guide - 48 1 1-49 Setting up PostScript or PCL printing with Windows 6. Click OK. Completing the Windows 2000/XP/Server 2003 printer connection To print from Windows 2000/XP/Server 2003, you must: · Set up network servers, if any. · Set up the Fiery to accept print jobs from your computer. · Configure a port on each Windows 2000/XP/Server 2003 computer for the network type. To do this Configure the parallel connection Configure the TCP/IP (LPR port) connection See "Completing the Windows 2000/XP/Server 2003 parallel port connection" in this section. "Completing the Windows 2000/XP/Server 2003 TCP/IP and Port 9100 or LPR connection" on page 1-51. "Completing the Windows 2000/XP/Server 2003 IPX (Novell) connection" on page 1-52. Configure the IPX (Novell) connection Note: The procedures for completing the printer connection for Windows 2000/XP and Windows Server 2003 are similar. Windows 2000 illustrations are used in the following procedure, with relevant Windows XP differences noted. Sharp AR-C360P EFI User's Software Installation Guide - 49 1 1-50 Installing User Software on a Windows Computer Completing the Windows 2000/XP/Server 2003 parallel port connection The parallel port cable connects the Fiery to a single computer. Once you have installed the Windows 2000/XP/Server 2003 PostScript printer driver and the Fiery printer description files, complete the setup for parallel port printing. To set up parallel printing for Windows 2000/XP/Server 2003 1. Windows 2000: Click Start, choose Settings, and then choose Printers. Windows XP: Click Start, and choose Printers and Faxes. [. . . ] For more information about Network Setup and Printer Setup, see Chapter 4 of the Configuration Guide. To set up client workstations to use Fiery WebTools 1. Make sure the workstation has a valid, unique IP address. Make sure a supported Internet browser is installed on the computer. For more information on supported browsers, see "System requirements" on page -12. 4. [. . . ]