User manual SHARP AR-M150/M155

[. . . ] MODEL AR-M150 AR-M155 DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF". If your copier is so marked, please read "I" for "ON" and " " for "OFF". For a complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. If the AR-M150/AR-M155 is used without the facsimile expansion kit AR-FX9, then the following directives are applicable : If the AR-M150/AR-M155 is used with the facsimile expansion kit AR-FX9, please refer to the Declaration Of Conformity in the AR-FX9 operation manual. [. . . ] · The factory default setting for the exposure level is "centre". 15 KEY TOUCH SOUND SOUND AT DEFAULT 16 17 TONER SAVE MODE 1: ON 2: OFF 18 1: SPF/RSPF AE LEVEL ADJUST 2: DOCUMENT GLASS 19 LANGUAGE 1: AMERICAN ENGLISH 2: ENGLISH 3: FRENCH 4: SPANISH 5: GERMAN 6: ITALIAN 7: DUTCH · This is used to set the 8: SWEDISH language used in the display. 9: NORWEGIAN 10: FINNISH 11: DANISH 12: HUNGARIAN 13: CZECH 14: POLISH 15: RUSSIAN 16: SLOVAK 1: YES 2: NO 1: ON 2: OFF 7 20 RESET FACTORY SORT AUTO SELECT · This is used to return all settings to the factory default settings. · Use this setting to enable or disable sort auto select mode. 21 65 USER SETTINGS Print mode Program number Program name Setting codes (factory default setting appears in bold) Explanation 1 FORCED OUTPUT 1: ON 2: OFF · When this function is enabled, printing in printer mode will automatically continue using a different size of paper if the specified size of paper runs out in all trays. This feature does not function in copy mode. 2 USB 2. 0 MODE SWITCH*1 · This sets the USB 2. 0 data transfer speed. To obtain the fastest speed when using the USB 2. 0 connector, first verify that your computer meets the system requirements (operating system and driver), and then use this program to 1: FULL-SPEED change the USB 2. 0 mode to 2: HI-SPEED "Hi-Speed". Note that the setting should not be changed while running a TWAIN driver. (For the system requirements, see "System requirements for USB 2. 0 (Hi-Speed mode)" (p. 57). ) · If the paper runs out during printing and there is paper of the same size in another tray, this function automatically switches to that tray (excluding the bypass tray). The function can be disabled. 3 AUTO TRAY SWITCH*2 1: ON 2: OFF *1 The scanning speed increases when the USB 2. 0 mode is set to "HI-SPEED", however, the printing speed does not increase considerably. *2 When the 250-sheet paper feed unit is installed. 66 SELECTING A SETTING FOR A USER PROGRAM 1 Press the [MENU] key and then press the [OK] key. In printer mode, the user programs are accessed by simply pressing the [MENU] key. MAIN MENU 1:USER PROGRAM 1, 2, 3, 1, 2, 3, SP. FUNC 2 Press the [ ] key ( ) or [ ] key ( ) to select the item that you wish to configure in the USER PROGRAM items, and then press the [OK] key. · See "USER PROGRAM" (p. 62 to p. 66) for the program name and program code. · You can also select a program by directly entering the program number with the numeric keys. USER PROGRAM 2:PREHEAT MODE 1, 2, 3, 1, 2, 3, SP. FUNC 3 Press the [ ] key ( ) or [ ] key ( ) to change the setting of the selected item. See "USER PROGRAM" (p. 62 to p. 66) for the program code. PREHEAT MODE 1:30 sec 1, 2, 3, 1, 2, 3, SP. FUNC Note · If you mistakenly select the wrong item, press the [CLEAR] key ( ) and repeat the procedure from step 2. · To cancel a setting for a user program, press the [MENU] key. 4 Press the [OK] key. Your selection appears briefly and then the previous screen appears. 7 Note When "AE LEVEL ADJUST" is selected in the user programs and the [OK] key is pressed, the automatic exposure adjustment screen appears. Adjust the exposure and press the [OK] key. 67 USER SETTINGS Audible signals (key entry beep, invalid key beep, base setting beep) The machine sounds three different types of beep signals: a key entry beep that sounds when a valid key is pressed, an invalid key beep that sounds when an invalid key is pressed, and a base setting beep that sounds when a setting is the same as the base setting (base settings are explained below). The base setting beep is initially disabled. If you wish to enable the base setting beep, see "SOUND AT DEFAULT" on page 65. If you wish to change the volume of the beep signals or disable them, see "KEY TOUCH SOUND" on page 65. The beep patterns of each type of beep signal are as follows: Key entry beep. . . . . . . . . . . . . . . . . . . . . One beep Invalid key beep. . . . . . . . . . . . . . . . . Three beeps Base settings The base settings are preset standard selections for each copy setting. The base settings are as follows: Copy ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Studies performed in animal models other than rats did not show any association between carbon black and lung tumors. Moreover, a two-year cancer bioassay using a typical toner preparation containing carbon black demonstrated no association between toner exposure and tumor development in rats. : In a study in rats of chronic inhalation exposure to a typical toner, a mild to moderate degree 3 of lung fibrosis was observed in 92% of the rats in the high concentration (16mg/m ) exposure group, and a minimal to mild degree of fibrosis was noted in 22% of the animals 3 in the middle (4mg/m ) exposure group, but no pulmonary change was reported in the 3 lowest (1mg/m ) exposure group, the most relevant level to potential human exposures. Chronic Effect 12. ECOLOGICAL INFORMATION No data are available. MATERIAL SAFETY DATA SHEET Page: 4/4 Date Revised :Jul. 31, 2002 Date Issued :Nov. 1. F-31001 13. DISPOSAL CONSIDERATION : Waste material may be dumped or incinerated under conditions which meet all federal, state and local environmental regulations. [. . . ]