User manual SHARP AR-M160/205

[. . . ] MODEL AR-M160 AR-M205 DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL Page AR-M160 · BEFORE USING THE MACHINE · COPY FUNCTIONS · CONVENIENT COPY FUNCTIONS · PRINTER/SCANNER FUNCTIONS · USER SETTINGS · TROUBLESHOOTING · ROUTINE MAINTENANCE · PERIPHERAL DEVICES AND SUPPLIES · APPENDIX 8 18 32 38 42 52 71 74 77 AR-M205 Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from copying by national law. Other items may be prohibited by local law. G Money G Checks G Stamps G Passports G Bonds G Stocks G Bank drafts G Driver's licenses In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF". [. . . ] · Use this setting to select the layout pattern when two original pages are copied onto a single sheet of paper (see page 34 for the layout patterns). · Use this setting to select the layout pattern when four original pages are copied onto a single sheet of paper (see page 34 for the layout patterns). · When enabled, this function offsets the position in the paper output tray of interrupt copy jobs and sets of copies during sort/group copy, and print jobs when using the printer function. · When a one-sided vertical (portrait) original is placed in a horizontal orientation (B4 or A3 (8-1/2" x 14" or 11" x 17") size) for two-sided copying, the top and bottom of the images on the front and back of the paper will be opposite to each other. · Use this setting to switch between the margin at the top edge and the margin at the left edge. 7 Rotation copy*2 0: OFF 1: ON 8 Auto paper select mode 0: OFF 1: ON 9 Auto tray switching 0: OFF 1: ON ­ 1: 0 mm (0") 2: 5 mm (1/4") 3: 10 mm (1/2") 4: 15 mm (3/4") 5: 20 mm (1") *2 10 to 15 Auditing mode Erase width adjustment*2 16 17 Layout in 2 IN 1 copy 1: Pattern 1 2: Pattern 2 1: Pattern 1 2: Pattern 2 3: Pattern 3 4: Pattern 4 0: OFF 1: ON 5 18 Layout in 4 IN 1copy*2 19 Offset of paper output tray 20 Image rotation in duplex copying*3 0: OFF 1: ON 21 Location of the margin*2, *3 Margin width*2 22 1: Left edge 2: Top edge 1: 0 mm (0") 2: 5 mm (1/4") 3: 10 mm (1/2") 4: 15 mm (3/4") 5: 20 mm (1") 1: 300dpi 2: 600dpi · Use this setting to set the margin width. 23 Resolution in Auto/Text mode · The copy resolution in auto and text mode is normally 300 dpi. If high-quality copies are preferred, use this setting to change the resolution to 600 dpi. *2 On models with a dual function board. *3 On models with automatic two-sided copying. 45 USER SETTINGS Program number Program name 24 Memory allocated to printer mode Setting codes (factory default setting appears in bold) 1: 30% 2: 40% 3: 50% 4: 60% 5: 70% Explanation · Use this to change the proportion of machine memory used for printer mode. · Use this setting to select whether or not holding down a key causes repeated input of the key. For keys that normally cause a set value to increase when held down (for example, holding down the [ZOOM] key ( , )), this program can be used to have the set value not change when the key is held down. · Use this setting to select how long a key must be pressed for the input to be accepted. By selecting a longer time, you can prevent settings from being changed by the accidental pressing of a key. 25 Key auto repeat 0: OFF 1: ON 26 27 28 29 1: Minimum (current response speed) Key press time 2: 0. 5 sec. 1: Low (current volume) Audible signals volume 2: High 3: OFF Base setting beep 0: OFF signal 1: ON 1: 99 copies Number of copies limit 2: 999 copies 0: OFF 1: ON 1: Upper paper tray*4 2: Lower paper tray*4 3: 250-sheet paper feed unit/ Upper paper tray of 2 x 250-sheet paper*4 feed unit 4: Lower paper tray of 2 x 250-sheet paper feed unit*4 5: Bypass tray*4 1: AUTO 2: TEXT 3: PHOTO · This sets the volume of beep signals. (p. 47) · Use this to sound a beep when a base setting is selected. (p. 47) · Use this setting to select 99 or 999 for the maximum number of copies. · When this function is enabled, printing in printer mode will automatically continue using a different size of paper if the specified size of paper runs out in all trays. This feature does not function in copy mode. 30 Use close paper size 31 Default tray setting · Use this program to select a default tray. This tray is automatically selected each time the power is turned on or each time the machine reverts to the initial settings. 32 Default exposure mode · Use this program to set "AUTO", "TEXT", or "PHOTO" as the default exposure mode. · This sets the USB 2. 0 data transfer speed. To obtain the fastest speed when using the USB 2. 0 port, first verify that your computer meets the system requirements (operating system and driver), and then use this program to change the USB 2. 0 mode to "Hi-Speed". Note that the setting should not be changed while running a TWAIN driver. (For the system requirements, see "System requirements for USB 2. 0 (Hi-Speed mode)" (p. 38). ) 33 USB 2. 0 mode switching*5 1: Full-Speed 2: Hi-Speed *4 AR-M160 is as follows: 1: Upper tray (factory default), 2: 250-sheet paper feed unit/Upper paper tray of 2 x 250-sheet paper feed unit, 3: Lower paper tray of 2 x 250-sheet paper feed unit, 5: Bypass tray *5 The scanning speed increases when the USB 2. 0 mode is set to "Hi-Speed", however, the printing speed does not increase considerably. 46 USER SETTINGS SELECTING A SETTING FOR A USER PROGRAM 1 Hold down the [Light] key ( the alarm indicators ( , , ) blink. ) until , , 4 Enter the desired setting code by pressing a numeric key. · For the setting codes, see "USER PROGRAMS". [. . . ] - Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic exposure level, setting . . . . . . . . . . . . . . . . . . . . . . . . . . Toner save mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . User programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]