User manual SHARP AR-200

[. . . ] MODEL AR-200 DIGITAL COPYING MACHINE OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · STATUS INDICATORS · GENERAL INFORMATION · OPTIONAL EQUIPMENT · APPENDIX 2 13 27 37 55 71 CAUTIONS Follow the cautions below when using this copier. q q The fusing area is hot. Exercise care in this area when removing misfed paper. Do not look directly at the light source. Doing so may damage your eyes. q q q Place the copier on a firm, level surface. [. . . ] The program numbers are shown in the table below. For example, to change the setting of the auto power shut-off timer, press key 3. Program name Auto clear time Preheat mode Auto power shut-off timer Stream feeding mode Auto power shut-off setting Border line for 2 in 1 or 4 in 1 Rotation copy Auto paper select mode Auto tray switching Auditing mode Account number entry Account number change Account number deletion Number of copies per account Resetting account Erase width adjustment Layout in 2 in 1 copy Layout in 4 in 1 copy Offset of paper output tray Program No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 ) key. The q GENERAL INFORMATION For operation of these programs after step 3, see page 40. User programs 3 Press the START key. q For programs 1 to 9 and 16 to 19, the entered program number will be steadily lit on the left side of the copy quantity display and the currently selected parameter number for the program will blink on the right side. For programs 10 to 15 (programs for auditing accounts), the display varies with the program number. See page 40 for setting programs 10 to 15. q 38 USER PROGRAMS 4 Select the desired parameter using the numeric keys. q The entered parameter number will blink on the right side of the copy quantity display. The parameters are shown in the table below. For example, to change the setting of the auto power shut-off timer to 60 min. , press key 2. q Parameters 0 e OFF 1 e 30 sec. Stream feeding mode * 0 e OFF 1 e ON Auto power shut-off setting 0 e OFF * 1 e ON Border line for 2 in 1 or 4 in 1 * 0 e OFF 1 e ON Rotation copy 0 e OFF * 1 e ON Auto paper select mode 0 e OFF * 1 e ON Auto tray switching 0 e OFF * 1 e ON Erase width adjustment 0 e 0 mm 1 e 5 mm Layout in 2 in 1 copy * 1 e Pattern 1 2 e Pattern 2 Layout in 4 in 1 copy * 1 e Pattern 1 2 e Pattern 2 Offset of paper output tray 0 e Upper OFF, lower OFF 2 e Upper ON, lower OFF Program name Auto clear time * 2 e 60 sec. 5 e 240 min. * 2 e 10 mm 3 e 15 mm 4 e 20 mm 3 e Pattern 3 4 e Pattern 4 * 1e Upper ON, lower ON 3 e Upper OFF, lower ON GENERAL INFORMATION Factory default settings are indicated with an asterisk (*). For layout in 2 in 1 copy and 4 in 1 copy, see page 63. If you select "0" (OFF) in a program, the corresponding function will be disabled. 5 Press the START key. q The right-hand number in the copy quantity display will be steadily lit and the entered value will be stored. User programs 6 To continue with other user programs, press the key and then repeat steps 2 to 5. To exit the user program mode, press the light ( ) key. q All the alarm indicators will go out. 39 USER PROGRAMS Settings for auditing accounts Setting of user programs No. 10 to 15 varies with the program number. For settings of all programs, first follow steps 1 to 3 in "Setting the user programs" on page 38 to select a program. Press the light ( ) key for more than 5 seconds. Enter a program number (10 to 15) using the numeric keys. Press the START key. ) Then follow the appropriate instructions for the program. Program No. 10: Auditing mode If the auditing mode is enabled, copying is limited to operators with an assigned 3-digit account number. A maximum of 20, 3-digit account numbers can be assigned. 10 is entered, the current setting (0: OFF, 1:ON) will blink on the right side of the copy quantity display. 1. Select the desired setting using the numeric keys. 0: 1: OFF ON 2. Press the START key. q The setting will be stored. 3. GENERAL INFORMATION User programs To continue with other user programs, press the key and enter another program number. [. . . ] Waste Disposal Method: Waste material may be dumped or incinerated under conditions which meet all federal, state and local environmental regulations. Section 10. Regulatory Information NFPA Rating (U. S. A. ): WHMIS Legislation (Canada): Transport Information: UN No. : Health = 1 Flammability = 1 This product is not a controlled product. This product is not a hazardous material. Other Information References: IARC (1996) IARC Monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans, Vol. [. . . ]