User manual SHARP BD-HP21SB

[. . . ] POLSKI BD-HP21SB ODTWARZACZ BLU-RAY BLU-RAY LEMEZLEJÁTSZÓ PEHRÁVAC DISK BLU-RAY PREHRÁVAC DISKOV BLU-RAY BLU-RAY DISK OYNATICI BLU-RAY BLU-RAY DISC PLAYER INSTRUKCJA OBSLUGI KEZELÉSI KÉZIKÖNYV NÁVOD K POUZITÍ NÁVOD NA POUZITIE KULLANIM KILAVUZU OPERATION MANUAL MAGYAR CESKY SLOVENSKY TÜRKÇE ENGLISH Introduction OPERATION MANUAL SAFETY INFORMATION Note: This Player can be used only where the power supply is AC 100-240V, 50/60Hz. It cannot be used elsewhere. ENGLISH Power Cord Protection To avoid any malfunctions of the Player, and to protect against electric shock, fire or personal injury, please observe the following. · Hold the plug firmly when connecting or disconnecting the AC power cord. · Keep the AC power cord away from heating appliances. · Never put any heavy object on the AC power cord. [. . . ] 2: Firmly connect the AV cable (supplied) to the audio jacks (1 and 2). This Player (Red) Connection (White) 1 To 2CH AUDIO output jacks AV cable (supplied) To audio input jacks (White) (Red) 2 Amplifier TV Audio equipment with audio jacks After connecting · Load a disc and start playback. (Pages 24-27) 19 Disc Playback Before Starting Playback Loading the Batteries in the Remote Control Approximate operating range of remote control Remote control sensor 1 Hold in the tab on the battery cover and pull the cover towards the direction of the arrow. 30º 7m 30º 2 Load the two "AA" size batteries (R-06 size, UM/SUM-3). Place batteries with their terminals corresponding to the m and n indications in battery compartment. Remote control unit 3 Insert the smaller tab of the battery cover into the opening 1, and press down on the cover until it clicks in place 2. Connecting the Power Cord Plug the supplied AC cord into the AC IN terminal on the rear of the Player. Then plug into AC outlet. NOTE · Do not subject the remote control unit to shock, water or excessive humidity. · The remote control unit may not function if the Player's remote sensor is in direct sunlight or any other strong light. · Incorrect use of batteries may cause them to leak or burst. Read the battery warnings and use the batteries properly. · Do not mix old and new batteries, or mix different brands. · Remove the batteries if you will not use the remote control unit for an extended period of time. To AC IN terminal To AC outlet NOTE · Place the Player close to the AC outlet, and keep the power plug within reach. · TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT TOUCH THE UN-INSULATED PARTS OF ANY CABLES WHILE THE AC CORD IS CONNECTED. · The a (STANDBY) indicator blinks while the Player is preparing for starting up. You cannot turn the Player on until the a (STANDBY) indicator stops blinking. 20 Before Starting Playback Setting the Remote Control Code · 3 types of remote control codes operate this Player: RC-1, RC-2 and RC-3. If you operate this Player by remote control along with another SHARP Blu-ray Disc Player or DVD Player placed next to it simultaneously, switching the remote control code (both the Player and remote control) to one of the signals (RC-1, RC-2 or RC-3) will let you operate only with this Player. · Make sure to set the Player and remote control to the same remote code. You can not operate the Player if they are not set to the same code. Operating the TV of SHARP Using the Remote Control The Universal Remote Control may operate the basic functions of the TV of SHARP. TV function control · · · · TV Power: B TV Channel up/down: P r/s TV Volume up/down: i e/f TV-AV Selector: b Setting the Remote Control Code of the Remote Example: Setting the code to "RC-3". 1 2 Press and hold 3 first and then B on the remote control together for more than 5 seconds. Press B (on the player) to turn off the player. B (POWER) Setting the Remote Control Code of the Player Disc Playback 3 Point the remote control at the player, then press and hold the DISPLAY button for more than 10 seconds. Remote control sensor 4 Press B (on the remote control) to turn on the player. 21 Before Starting Playback Turning the Power On Turning the power on Press B on the remote control or on the Player to turn on the power of the Player. Language Setting Changing the on-screen display language 1 Press SETUP to display the SETUP MENU screen. Entering standby Press B on the remote control or on the Player to enter standby. 2 Press a/b/c/d to select "ON SCREEN LANGUAGE", then press ENTER. DISPLAYS THE TITLE LIST SETTINGS · If you press B again immediately after entering standby, the Player may not turn on. If this happens, wait for 10 seconds or more and then turn on the power again. NOTE · When the a (STANDBY) indicator is blinking (may take some time), the Player cannot be turned on. B (POWER) ON SCREEN LANGUAGE PICTURE 3 Press a/b/c/d to select the language you want to display on the screen, then press ENTER. ENGLISH SLOVENSKY DEUTSCH FRANÇAIS ITALIANO BD/DVD/CD mode indicator I (ON) indicator POLSKI CESKY MAGYAR a (STANDBY) indicator NOTE Indicators on the Player I (ON) indicator Green on Power on · To select the DVD disc language, such as subtitle language, etc. , see page 25. a (STANDBY) indicator Red blinks Red on Preparing for standby Standby BD/DVD/CD mode indicator Off Blue on White on White blinks No disc Playing back Disc stopped Loading a disc · When you turn on the POWER, the MENU screen automatically displays for a while. Press EXIT to erase the display. 22 Before Starting Playback Turning Off the LCD Backlight and Indications If you feel that the indicators on the Player are too bright when watching movies, you can turn them off except for the I (ON) indicator. Using AQUOS LINK Controlling the Blu-ray disc player using AQUOS LINK What is AQUOS LINK? Using the HDMI CEC (Consumer Electronics Control), with AQUOS LINK you can interactively operate this player. 1 2 3 Press SETUP to display the SETUP MENU screen. Press a/b/c/d to select "SETTINGS", then press ENTER. Press a/b to select "FRONT DISPLAY/LED", then press ENTER. What you can do with AQUOS LINK When you connect this player to the LCD TV compatible with AQUOS LINK using an HDMI cable, you can perform the function listed below. (See page 15 for connecting to the HDMI terminal. ) AUDIO VIDEO SETTINGS QUICK START AUTO POWER OFF AQUOS LINK PLAYBACK SETTING FRONT DISPLAY/LED VERSION USB MEMORY MANAGEMENT SOFTWARE UPDATE SYSTEM RESET Playback function turns on the LCD TV immediately. When you start to playback of this player, Power of LCD TV will be turned on and the playback image will appear on the screen. Automatic input select function 4 5 Press c/d to select "ON" or "OFF", then press ENTER. [. . . ] 41 Glossary Letter Box (LB 4:3) (page 35) A screen size with black bars on the top and bottom of the image to allow viewing of wide-screen (16:9) material on a connected 4:3 TV. Resume playback (page 24) If you stop playback while it is in progress, the Player stores the stop position in memory, and this function lets you playback from that point. Linear PCM Sound Linear PCM is a signal recording format used for Audio CDs and on some DVD and Blu-ray discs. The sound on Audio CDs is recorded at 44. 1 kHz with 16 bits. (Sound is recorded between 48 kHz with 16 bits and 96 kHz with 24 bits on DVD video discs and between 48 kHz with 16 bits and 192 kHz with 24 bits on BD video discs. ) Skip (page 28) This returns to the start of the chapter (or track) being played, or skips to the next chapter (or track). Subtitles (pages 29, 32, 33) These are the lines of text appearing at the bottom of the screen which translate or transcribe the dialogue. They are recorded on many DVD and BD video discs. MPEG-2 MPEG-2 (Moving Picture Experts Group phase 2) is one of the video data compression schemes, which is adopted for DVD videos and digital broadcasts worldwide. [. . . ]