User manual SHARP CD-BA2000H

[. . . ] To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. Special Notes Warning: Important Instruction - Introduction / Special Notes - z When the ON/STAND-BY button is set at STAND-BY position, mains voltage is still present inside the unit. When the ON/STAND-BY button is set at STAND-BY position, the unit may be brought into operation by the timer mode or remote control. z This unit contains no user serviceable parts. [. . . ] Change the lighting or the direction of the unit. z Keep the remote control away from moisture, heat, shock, and vibrations. To change the tuning zone: 1 Press the ON/STAND-BY button to enter the stand-by mode. 2 Set the SPAN SELECTOR switch (on the rear panel) as follows. z For 50 kHz FM interval (9 kHz in AM) 50/9 z For 100 kHz FM interval (10 kHz in AM) 100/10 3 Whilst pressing down the / button and the EQUALIZER/X-BASS/DEMO button, press the ON/STAND-BY button until "CLEAR AL" appears. , , Test of the remote control Face the remote control directly to the remote sensor on the unit. Remote sensor 0. 2 m - 6 m (8" - 20') Caution: This operation will erase all data stored in memory including clock, timer settings, tuner preset, and CD programme. The remote control can be used within the range shown: Press the ON/STAND-BY button. Now, you can enjoy the music. E-9 ENGLISH General Control , , Extra bass (X-BASS)/Pre-programmed equaliser (Main unit operation) You can select the extra bass and pre-programmed equaliser modes with the same button on the main unit. CD-BA2000H Changing the mode: When the EQUALIZER/X-BASS/DEMO button is pressed, the current mode setting will be displayed. To change to a different mode, press the EQUALIZER/X-BASS/ DEMO button repeatedly until the desired sound mode appears. FLAT (X-BASS on) ROCK (X-BASS on) POPS (X-BASS on) VOCAL (X-BASS off) JAZZ (X-BASS off) POPS (X-BASS off) ROCK (X-BASS off) FLAT (X-BASS off) Basic Operation CLASSIC (X-BASS off) , , Demonstration mode The first time the unit is plugged, the unit will enter the demonstration mode. You will see words scroll. JAZZ (X-BASS on) CLASSIC (X-BASS on) VOCAL (X-BASS on) To cancel the demonstration mode: When the unit is in the power stand-by mode (demonstration mode), press the EQUALIZER/X-BASS/DEMO button. The demonstration mode will be cancelled and the display will disappear. (Remote control operation) To enter or cancel the extra bass mode: When the power is first turned on, the unit will enter the extra bass mode which emphasises the bass frequencies, and "X-BASS" will appear. To cancel the extra bass mode, press the X-BASS button. To return to the demonstration mode: When the unit is in the power stand-by mode, press the EQUALIZER/X-BASS/DEMO button again. Note: When the power is on, the EQUALIZER/X-BASS/DEMO button can be used to select the extra bass mode. Selecting a pre-programmed equaliser mode: When the EQUALIZER MODE button is pressed, the current mode setting will be displayed. To change to a different mode, press the EQUALIZER MODE button repeatedly until the desired sound mode appears. , , To turn the power on To set the unit to stand-by mode: Press the ON/STAND-BY button again. Press the ON/STAND-BY button to turn the power on. FLAT ROCK POPS button for The sound is not modified. Bass and treble are slightly emphasised. z You can skip to any track by pressing the button repeatedly until the desired track number appears. - Listening to a CD (CDs) - CD Playback To interrupt playback: Press the button on the remote control. To resume playback from the same point, press the button. Note: You can locate the beginning of a track on a single disc only. , , To locate the desired portion For audible fast forward: Press and hold down the button during playback. To stop playback: Press the (CD ) button. To remove the CDs: Whilst in the stop mode, press the OPEN/CLOSE button. Then, press the DISC SKIP button to rotate the disc tray and remove the remaining disc. For audible fast reverse: Press and hold down the button during playback. After use: Press the ON/STAND-BY button to enter the power stand-by mode. Caution: z z z z z Do not place two CDs in one disc tray. Do not push the disc tray whilst it is moving. If the power fails whilst the tray is open, wait until the power is restored. If the disc tray is stopped forcibly, "ERR 0203" will appear in the display and the unit will not function. If this occurs, press the ON/STAND-BY button to enter the power stand-by mode and then turn the power on again. z If TV or radio interference occurs during CD operation, move the unit away from the TV or radio. z If a disc is damaged, dirty, or loaded upside down, the disc will be skipped. Notes: z Normal playback will resume when the or button is released. z You can locate the desired portion on a single disc only. z When the end of the last track is reached during fast forward, "END" will appear on the display and CD operation will be paused. [. . . ] TAPE 1 and TAPE 2 will simultaneously stop. Erase-prevention tab of cassette tapes: z When recording on a cassette tape, make sure that the erase-prevention tabs are not removed. Cassettes have removable tabs that prevent accidental recording or erasing. Tab for side B z To protect the recorded sound, remove the tab after recording. Cover the tab hole with adhesive tape to record on the tape without the tab. Side A , , Erasing recorded tapes 1 2 3 4 Load the tape to be erased into the TAPE 2 cassette compartment with the side to be erased facing toward you. [. . . ]