User manual SHARP CD-C470H

[. . . ] To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. Special Notes Important Instruction CAUTION - Introduction / Special Notes - Laser Diode Properties Material: GaAIAs Wavelength: 780 nm Emission Duration: continuous Laser Output: max. 0. 6 mW z This Mini Component System is classified as a CLASS 1 LASER product. z The CLASS 1 LASER PRODUCT label is located on the rear cover. [. . . ] If the time display is flashing, step 3 (for selecting the 24-hour or 12-hour display) will be skipped. (AM 0:00 - PM 11:59) Note that this can only be set when the unit is first installed or it has been reset. [Refer to "Clearing all the memory (reset)" on page 31 for details. ] To change the 24-hour or 12-hour display: 1 2 Clear all the programmed contents. [Refer to "Clearing all the memory (reset)" on page 31 for details. ] Perform "Setting the Clock" from the beginning. E-13 ENGLISH Listening to a CD (CDs) This system can play audio CD-R and CD-RW discs just as CD discs, but cannot perform recording. (However, some CD-R and CD-RW discs may not be played. ) , , To play discs in turn (from Disc 1 to Disc 6) 1 2 3 4 Press the ON/STAND-BY button to turn the power on. Press the 1 button to open the disc tray 1. Place the CD on the disc tray 1, label side up. Be sure to place 8 cm (3") CD in the middle of the disc trays. 12 cm (5") 8 cm (3") 5 Press the 1 button to close the disc tray 1. Total number of tracks Total playing time Music schedule Means "disc inside" The music schedule will display only the number of tracks on the disc. If the CD contains more than 15 tracks, " " will appear. 6 You can place discs on the trays 2 - 6 by following steps 3 - 5. Note: The system will search CD trays until it finds a CD and will not search the rest of the trays. Continued to the next page Sound Control (See page 12. ) ENGLISH E-14 - Listening to a CD (CDs) - CD Playback Listening to a CD (CDs) (continued) 7 Press the ( ) button to start playback. , , To locate the beginning of a track To move to the beginning of the next track: Press the / button for less than 0. 5 seconds during playback. z You can skip to any track by pressing the / button repeatedly until the desired track number appears. z Playback will begin from track 1 on the DISC 1. After that disc finishes playing, the next disc will automatically play. z When the last track on the DISC 6 has finished playing, the CD player will stop automatically. To restart the track being played: Press the / button for less than 0. 5 seconds during playback. z You can skip to any track by pressing the / button repeatedly until the desired track number appears. - Listening to a CD (CDs) - CD Playback z When there is no CD in one of the disc tray 1 - 6 positions, that position will be skipped and the next CD will be played. To interrupt playback: Press the button on the remote control. Press the Press the Note: During programme play, buttons 16 will not work. button. ( ) button to start playback. CD Playback To clear the programmed selections: - Programmed Play - Press the CLEAR button on the remote control whilst the "MEMORY" indicator is flashing. Each time the button is pressed, one track will be cleared, beginning with the last track programmed. To cancel the programmed play mode: 1 Whilst in the stop mode, press the MEMORY/SET (MEMORY) button to enter the programming save mode. Whilst in the stop mode and the "MEMORY" indicator is lit, press the CLEAR button on the remote control. The "MEMORY" indicator will disappear and all the programmed contents will be cleared. Adding tracks to the programme: If a programme has been previously stored, the "MEMORY" indicator will be displayed. The new tracks will be stored after the last track of the original programme. 2 Press one of the 1 - 6 buttons to select the desired disc. Selected disc number To check which tracks are programmed: Whilst the unit is stopped in the programmed play mode, press the button. / or / Notes: 3 Press the / or / button to select the desired track. Selected track number Playback order z Opening any tray of the programmed discs automatically cancels the programmed sequence. z Even if you press the ON/STAND-BY button to enter the stand-by mode or change the function from CD to another, the programmed selections will not be cleared. z During programme operation, random play is not possible. E-17 ENGLISH Listening to the Radio 1 2 3 Press the ON/STAND-BY button to turn the power on. Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM). Manual tuning: or ) button to tune in to the desired Press the TUNING/TIME button as many times as required to tune in to the desired station. Auto tuning: z When radio interference occurs, auto scan tuning may stop automatically at that point. z Auto scan tuning will skip weak signal stations. [. . . ] (Refer to page 31. ) z No sound is heard. z z z z Is the volume level set to "0"?Is the karaoke mode set to "L-CH", "R-CH" or "V-CANCEL"? , , Karaoke Symptom z The vocal part of a multiplexed disc is not heard. Possible cause z Is the karaoke mode set to "L-CH", "R-CH" or "V-CANCEL"? , , CD player Symptom Possible cause z Playback does not start. [. . . ]