User manual SHARP CD-C611H

[. . . ] Customers without Internet access may telephone 08705 274277 during office hours (or (01) 676 0648 if telephoning from Ireland). 0101 CD-C611H_FRONT 1 02. 1. 10, 9:13 AM CD-C611H Special notes NOTES FOR USERS IN THE U. K. AND IRELAND The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. Always refit the fuse cover after replacing the fuse. [. . . ] After that disc finishes playing, the next disc will automatically start playback. When the last track on the third disc has finished playing, the CD player will stop automatically. When there is no CD in one of the disc 1 - 3 positions, that position will be skipped and the next CD will be played. Place the CD(s) on the disc tray, label side up. When loading a third disc, press the DISC SKIP button to turn the disc tray, then place the CD in the open position. To interrupt playback: Press the CD button on the remote control. To resume playback from the same point, press the button. CDs can be placed on any open position on the disc tray. Be sure to place 8 cm (3") CD(s) in the middle of the disc positions. To stop playback: Press the (CD ) button. To remove the CDs: 12 cm (5") 8 cm (3") Whilst in the stop mode, press the OPEN/CLOSE button. Then, press the DISC SKIP button to rotate the disc tray and remove the remaining disc. After use: Press the ON/STAND-BY button to enter the power stand-by mode. 16 Sound control (See page 14. ) 02/1/8 CD-C611H(UK)_2. fm CD-C611H To locate the beginning of a track To move to the beginning of the next track: Press the / button for less than 0. 5 seconds during playback. You can skip to any track by pressing the / button repeatedly until the desired track number appears. Starting playback with a desired track You can play a disc starting with the desired track. 1 2 Whilst in the stop mode, press the DISC SKIP button to select the desired disc. Press the / or / button to select the desired track. To restart the track being played: Press the / button for less than 0. 5 seconds during playback. You can skip to any track by pressing the / button repeatedly until the desired track number appears. Selected disc number Notes: To locate the desired portion For audible fast forward: Press and hold down the Press and hold down the / / button during playback. button during playback. Selected track number You can also select a track by pressing the remote control. / or / button on the 3 Press the / ( ) button to start playback. Playback of the selected track is started. In random play, the CD player will select and play tracks automatically. (You cannot select the order of the tracks. ) Adding tracks to the programme: If a programme has been previously stored, the "MEMORY" indicator will be displayed. The new tracks will be stored after the last track of the original programme. Notes: Caution: After performing repeat or random play, be sure to press the wise, the disc(s) will play continuously. Other- Opening the disc tray automatically cancels the programmed sequence. Even if you press the ON/STAND-BY button to enter the stand-by mode or change the function from CD to another, the programmed selections will not be cleared. During programme operation, random play is not possible. 18 02/1/8 CD-C611H(UK)_2. fm Listening to the radio Tuning 1 2 3 Press the ON/STAND-BY button to turn the power on. Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM). Manual tuning: Press the TUNING/TIME button as many times as required to tune in to the desired station. CD-C611H or ) button to tune in to the desired Auto tuning: Notes: When radio interference occurs, auto scan tuning may stop automatically at that point. Auto scan tuning will skip weak signal stations. To stop the auto tuning, press the TUNING/TIME button again. To receive an FM stereo transmission: Press the TUNER (BAND) button to display the "ST" indicator. " " will appear when an FM broadcast is in stereo. [. . . ] 4 Press the OPEN/CLOSE button to close the disc tray. Make sure that "NO DISC" is displayed. 5 Press the ON/STAND-BY button to enter the stand-by mode, and then unplug the AC power lead from the wall socket. 6 Insert the transport screw into the back of the unit and tighten it with a flat head screwdriver or a coin. Condensation Sudden temperature changes, storage or operation in an extremely humid environment may cause condensation inside the cabinet (CD pickup, tape heads, etc. ) or on the transmitter on the remote control. [. . . ]