User manual SHARP CD-E100H

[. . . ] MINI KOMPONENTEN SYSTEM MINI-CHANE SISTEMA MINI MINI KOMPONENT SYSTEM MINI SISTEMI MINI SYSTEEM MINI SISTEMA DE COMPONENTES MINI COMPONENT SYSTEM MODELL MODLE MODELO MODELL MODELLO MODEL MODELO MODEL Mini Komponenten System CD-E100H besteht aus CD-E100H (Hauptgert) und CP-E100H (Lautsprecher-System). Mini-chane CD-E100H compose de CD-E100H (appareil principal) et de CPE100H (enceintes acoustiques). Sistema mini CD-E100H que consta de CD-E100H (aparato principal) y CP-E100H (sistema de altavoces). CD-E100H mini komponent system bestende av CD-E100H (huvudenhet) och CP-E100H (hgtalarsystem). [. . . ] Do not allow any objects to fall into or to be placed in the bass reflex ducts. Note: The speaker grilles are not removable. Incorrect Note: When the power is on, the EQUALIZER/X-BASS/DEMO button can be used to select the pre-programmed equaliser and extra bass modes. Connecting the AC power lead After checking all the connections have been made correctly, connect the AC power lead to the AC power input socket, then plug the AC power lead of this unit into the wall socket. If you plug in the unit first, the unit will enter the demonstration mode. Notes: Unplug the AC power lead from the wall socket if the unit will not be in use for a prolonged period of time. Never use a power lead other than the one supplied. Otherwise, a malfunction or an accident may occur. To turn the power on Press the ON/STAND-BY button to turn the power on. After use: Press the ON/STAND-BY button to enter the power stand-by mode. Preparation for Use T T Speaker connection Demonstration mode ENGLISH T T The first time the unit is plugged in, the unit will enter the demonstration mode. To cancel the demonstration mode: When the unit is in the power stand-by mode (demonstration mode), press the EQUALIZER/X-BASS/DEMO button. The unit will enter the low power consumption mode. To return to the demonstration mode: When the unit is in the power stand-by mode, press the EQUALIZER/X-BASS/DEMO button again. 8 E-8 03/1/21 08-CD-E100H(H)E1. fm CD-E100H Remote control Battery installation Remove the battery cover. Insert the batteries according to the direction indicated in the battery compartment. When inserting or removing the batteries, push them towards the battery terminals. 1 2 Notes concerning use: Replace the batteries if the operating distance is reduced or if the operation becomes erratic. Purchase 2 "AA" size batteries (UM/ SUM-3, R6, HP-7 or similar). Periodically clean the transmitter on the remote control and the sensor on the unit with a soft cloth. Exposing the sensor on the unit to strong light may interfere with operation. Change the lighting or the direction of the unit. Keep the remote control away from moisture, heat, shock, and vibrations. ENGLISH Preparation for Use Precautions for battery use: Replace all old batteries with new ones at the same time. Remove the batteries if the unit is not to be used for long periods of time. This will prevent potential damage due to battery leakage. Caution: Do not use rechargeable batteries (nickel-cadmium battery, etc. ). Installing the batteries incorrectly may cause the unit to malfunction. E-9 T T 3 Test of the remote control Check the remote control after checking all the connections (see pages 7 - 8). [. . . ] Is the FM aerial or AM loop aerial placed properly?Move the aerial away from the AC power lead if it's located nearby. z z z z z z z T T CD-E100H ENGLISH When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc. ) or if it is operated incorrectly, it may malfunction. If such a problem occurs, do the following: 1 Set the unit to the stand-by mode and turn the power on again. 2 If the unit is not restored in the previous operation, unplug and plug in the unit, and then turn the power on. [. . . ]