User manual SHARP CD-MPX500H

[. . . ] It will guide you in operating your SHARP product. Special Notes Important Instruction CAUTION Laser Diode Properties Material: GaAIAs Wavelength: 780 nm Emission Duration: continuous Laser Output: max. 0. 6 mW - Introduction / Special Notes - z This Mini Component System is classified as a CLASS 1 LASER product. z The CLASS 1 LASER PRODUCT label is located on the rear cover. z Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. [. . . ] When loading a third disc, press the DISC SKIP button to turn the disc tray, then place the CD in the open position. z CDs can be placed on any open position on the disc tray. z Be sure to place 8 cm (3") CD(s) in the middle of the disc positions. 5 Press the OPEN/CLOSE button to close the disc tray. Total number of tracks on the CD whose number is flashing Total playing time of the CD whose number is flashing 6 To select the CD you want to listen to first, press one of the 3 buttons. 1- Continued to the next page Sound Control (See page 12. ) ENGLISH E-14 CD Playback 12 cm (5") 8 cm (3") - Listening to a CD (CDs) - Listening to a CD (CDs) (continued) 7 Press the ( ) button to start playback. , , To locate the beginning of a track To move to the beginning of the next track: Press the PRESET button for less than 0. 5 seconds during playback. z You can skip to any track by pressing the PRESET button repeatedly until the desired track number appears. button for less than 0. 5 seconds during playback. z You can skip to any track by pressing the PRESET button repeatedly until the desired track number appears. z Playback will begin from track 1 on the disc you have selected to play. After that disc finishes playing, the next disc will automatically start playback. z When the last track on the third disc has finished playing, the CD player will stop automatically. z When there is no CD in one of the disc 1 - 3 positions, that position will be skipped and the next CD will be played. To restart the track being played: Press the PRESET - Listening to a CD (CDs) - CD Playback To interrupt playback: Press the button on the remote control. To resume playback from the same point, press the button. Notes: z You can locate the beginning of a track on a single disc only. z The PRESET / or PRESET / button on the remote control allows you to locate the beginning of a track. To stop playback: Press the button. , , To locate the desired portion For audible fast forward: Press and hold down the PRESET button during playback. To remove the CDs: Whilst in the stop mode, press the OPEN/CLOSE button. Then, press the DISC SKIP button to rotate the disc tray and remove the remaining disc. After use: Press the ON/STAND-BY button to enter the power stand-by mode. For audible fast reverse: Press and hold down the PRESET button during playback. Caution: z z z z z Do not place two CDs in one disc tray. Up to 32 tracks can be programmed. If you make a mistake, the programmed tracks can be cleared by pressing the CLEAR button. 5 Press the ( ) button to start playback. CD Playback - Programmed Play - To clear the programmed selections: Press the CLEAR button on the remote control whilst the "MEMORY" indicator is lit. Each time the button is pressed, one track will be cleared, beginning with the last track programmed. When all the tracks are cleared, "MEMORY" will disappear. Adding tracks to the programme: If a programme has been previously stored, the "MEMORY" indicator will be displayed. The new tracks will be stored after the last track of the original programme. 1 Whilst in the stop mode, press one of the 1 - 3 buttons to select the desired disc. Selected disc number Notes: z Opening the disc tray automatically cancels the programmed sequence. z Even if you press the ON/STAND-BY button to enter the stand-by mode or change the function from CD to another, the programmed selections will not be cleared. z During programme operation, random play is not possible. 2 Press the PRESET desired track. PRESET or button to select the You can also select a track by pressing the / button on the remote control. Selected track number PRESET / or PRESET E-17 ENGLISH Listening to the Radio 1 2 3 Press the ON/STAND-BY button to turn the power on. Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM). Manual tuning: or ) button to tune in to the desired CD-MPX500H Press the TUNING/TIME button as many times as required to tune in to the desired station. Auto tuning: When the TUNING/TIME button is pressed for more than 0. 5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station. Notes: z Auto scan tuning will skip weak signal stations. z To stop the auto tuning, press the TUNING/TIME button again. To receive an FM stereo transmission: Press the TUNER (BAND) button to display the "ST" indicator. z " " will appear when an FM broadcast is in stereo. FM stereo mode indicator FM stereo receiving indicator z If the FM reception is weak, press the TUNER (BAND) button to extinguish the "ST" indicator. [. . . ] (Refer to page 31. ) z No sound is heard. z z z z Is the volume level set to "0"?Is the karaoke mode set to "L-CH", "R-CH" or "V-CANCEL"? , , Karaoke Symptom z The vocal part of a multiplexed disc is not heard. Possible cause z Is the karaoke mode set to "L-CH", "R-CH" or "V-CANCEL"? , , CD player Symptom Possible cause z Playback does not start. [. . . ]