User manual SHARP CD-S3460/E

[. . . ] Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three pin plug. [. . . ] The unit searches for the same name within folders (or titles). 1 2 3 Perform steps 1 - 3 in "File search (by folder or title 1/2/3)" on page 23. Press the , , or cursor button on the remote control to select "FOL", "T-1", "T-2" or "T-3". To search files by folder name, select "FOL" (will flash). Folder Title 1 If the search word is not in the folder (or title) name, "NOT FOUND" appears and the menu returns. CD or MP3/WMA disc Playback 9 10 Use the or (or title). cursor button to scroll and select a folder Title 2 Title 3 4 Press the CHARACTER button for 2 seconds. The display will be ready for editing characters. 1st row: String table 2nd row: Input editor (8 digits) Press the alphabet. or or cursor button to select the desired button to go to the next page of character Press the / button to start playback. All files in the selected folder (or title) are played, and the previous display returns. 5 6 Press the CHARACTER button and the active character will be entered in the 2nd row of the display. To exit the MP3/WMA navigation mode: In the stop mode, press the CD button. Notes: The unit searches regardless of the case, and names found will appear in uppercase. Character entry with direct buttons: The direct buttons on the remote control can also be used for character entry. In step 5 on the left, use buttons 0 - 9 to enter alphabets. Alphabet types change as you press a button. Press the TUNING ( or ) button to tune in to the desired station. Manual tuning: Press the TUNING button as many times as required to tune in to the desired station. Auto tuning: When the TUNING button is pressed for more than 0. 5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station. Notes: When radio interference occurs, auto scan tuning may stop automatically at that point. Auto scan tuning will skip weak signal stations. To stop the auto tuning, press the TUNING button again. When an RDS (Radio Data System) station is tuned in, the frequency will be displayed first, and then the RDS indicator will light up. Full auto tuning can be achieved for RDS stations "ASPM", see page 33. To receive an FM stereo transmission: Press the TUNER (BAND) button to display the "ST" indicator. " " will appear when an FM broadcast is in stereo. If the FM reception is weak, press the TUNER (BAND) button to extinguish the "ST" indicator. The reception changes to monaural, and the sound becomes clearer. [. . . ] Fingerprints, dirt, or water on the CDs can cause noise or mistracking. If a CD is dirty or does not play properly, clean it with a soft, dry cloth, wiping straight out from the centre, along the radius. Clearing all the memory (reset) 1 2 Press the ON/STAND-BY button to enter the power stand-by mode. Whilst pressing down the button and the button, press the TUNER (BAND) button until "CLEAR ALL" appears. NO YES Correct References Caution: This operation will erase all data stored in memory including clock, timer settings, tuner preset, and CD programme. 1 2 3 4 5 6 7 45 13/2/06 CD-S3460/EE_EN. fm TINSZA165AWZZ CD-S3460/E Maintenance Cleaning the tape-handling parts Dirty heads, capstans or pinch rollers can cause poor sound and tape jams. Clean these parts with a cotton swab moistened with commercial head/pinch roller cleaner or isopropyl alcohol. [. . . ]