User manual SHARP CDBA160 OPERATION MANUAL PART (FROM SERVICE MANUAL)

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SHARP CDBA160. We hope that this SHARP CDBA160 user guide will be useful to you.

Lastmanuals help download the user guide SHARP CDBA160.

Download

Manual abstract: user guide SHARP CDBA160OPERATION MANUAL PART (FROM SERVICE MANUAL)

Detailed instructions for use are in the User's Guide.

 [. . . ] SETTING THE CLOCK
Remote control
Press the TUNING/TIME ( the hour. or ) button to adjust

PREPARATION FOR USE
RESETTING THE MICROCOMPUTER

In this example,  the clock is set for the 24-hour (0:00) system. 

6
Reset the microcomputer under the following conditions: To erase all of the stored memory contents (clock and timer settings,  and tuner and CD presets).  [. . . ] Keep the remote control away from moisture,  excessive heat,  shock,  and vibrations. 

4

Press the TUNING/TIME ( time display mode. 

or

) button to select the

To see the time display: Press the CLOCK button. The time display will appear for about 5 seconds. 

0:00

AM 0:00

AM 12:00

"0:00"

The 24-hour display will appear. (0:00 23:59)

"AM 0:00"

The 12-hour display will appear. (AM 0:00 - PM 11:59)

Note: The clock display will flash on and off at the push of the CLOCK button when the AC power supply is restored after a power failure occurs or after the AC power lead is disconnected. If this happens,  follow the procedure below to change the clock time. 

"AM 12:00"

The 12-hour display will appear. (AM 12:00 - PM 11:59)

Note that this can only be set when the unit is first installed or it has been reset (see page 33). 

To change the clock time: 1 Press the CLOCK button. 2 Within 5 seconds,  press the MEMORY/SET button. 3 Perform steps 6 - 9 above. 

5

Press the MEMORY/SET button. 

To change the time display mode: 1 Perform steps 1 - 2 in "RESETTING THE MICROCOMPUTER", . 2 Perform steps 1 - 9 above. 

1
4
Connections 1 Connect the AM and FM aerials. 
FM aerial AM loop aerial

Check the supplied accessories
1

FM aerial × 1

AM loop aerial × 1

Remote control × 1

(For U. K. ) (For Europe) AC power lead × 1

2

2
3 Replace the battery cover. 

Putting batteries into the remote control

1 Remove the battery cover. 

2 Insert the batteries. 

2 Connect the speaker system. 
Right speaker Left speaker Red Black With white line

q 2 "AA" size batteries

­7­
10 cm (4") 10 cm (4")

(UM/SUM-3,  R6,  HP-7 or similar)

3

Placing the system

10 cm (4")

10 cm (4")

3 Connect the AC power lead. 

AC 230 V,  50 Hz (For Europe) AC 230 V,  50 Hz (For U. K. )

CD-BA160H/1700H

5
Recording from CDs
1 4 5 3

Listening to a CD

8

4

5

12 cm (5")

CD-BA160H/1700H

8 cm (3")

1 Press the ON/STAND-BY button to turn the power on. 3 Press the OPEN/CLOSE button to open the disc tray.  [. . . ] q And then,  close the cassette door completely until it is locked. 

4 Press the TAPE (1

or TAPE 2. 

3

3

5 Press the button to start playback. 6 Adjust the sound volume using the VOLUME buttons. 
Cleaning disc

PUSH EJECT

2

TAPE 1

TAPE 2

2

PUSH EJECT [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP CDBA160

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP CDBA160 will begin.