User manual SHARP CDS3460E OPERATION MANUAL

[. . . ] When the ON/STAND-BY button is set at STAND-BY position, the unit may be brought into operation by the timer mode or remote control. Warning: This unit contains no user serviceable parts. Never remove covers unless qualified to do so. This unit contains dangerous voltages, always remove mains plug from the socket before any service operation and when not in use for a long period. [. . . ] q The time display will appear for about 5 seconds. Note: q The clock display will flash on and off at the push of the CLOCK button when the AC power supply is restored after a power failure occurs or after the AC power lead is disconnected. If this happens, follow the procedure below to change the clock time. To change the clock time: xPress the CLOCK button. yWithin 5 seconds, press the MEMORY/SET button. zPerform steps 6 - 9 above. To change the time display mode: xPerform steps 1 - 2 in the section "RESETTING THE MICROCOMPUTER", on page 23. yPerform steps 1 - 9 above. E-11 SOUND CONTROL (Main unit) (Remote control) s Volume Press the VOLUME button to increase the volume and the VOLUME button to decrease the volume. 0 1 2 . . . . . 29 30 MAXIMUM s Extra bass (X-BASS) (Main unit) (Remote control) When the power is first turned on, the unit will enter the extra bass mode which emphasises the bass frequencies, and "XBASS" will appear. To cancel the extra bass mode, press the X-BASS/DEMO (XBASS) button. "X-BASS" will disappear. X-BASS indicator s Pre-programmed equalizer (Main unit) (Remote control) When the EQUALIZER (EQUALIZER MODE) button is pressed, the current mode setting will be displayed. To change to a different mode, press the EQUALIZER (EQUALIZER MODE) button repeatedly. FLAT VOCAL ROCK CLASSIC POPS JAZZ FLAT: The sound is not modified. POPS: Bass and treble are slightly emphasised. VOCAL: Vocals (midrange tones) are emphasised. E-12 COMPACT DISC OPERATION 4 5 s CD playback 12 cm (5") 8 cm (3") 1 2 3 4 Press the ON/STAND-BY button to turn the power on. Press the 0 (0R) button. q The next disc playback will begin, after which each following disc will be played sequentially. Note: q When the DISC SKIP button is pressed during playback, playback will begin automatically from the next disc. (It is not necessary to press the 0 (0R) button. ) DISC SKIP s APSS (Auto Program Search System) DISC SKIP RANDOM APSS automatically locates the beginning of any track. To listen again to the track being played: Press the 5 (5 3) button for less than 0. 5 seconds during playback. To move to the beginning of the next track: Press the 4 (2 4) button for less than 0. 5 seconds during playback. q To skip a number of tracks at one time, press the 5 (5 3) or 4 (2 4) button repeatedly until the desired track number is shown. q To start playback from a desired track, press the 5 (5 3) or 4 (2 4) button whilst in the stop mode to select the track number, and then press the 0 (0R) button. Note: q APSS can only search for music on a single disc. s Random play (Remote control operation) The tracks on the disc(s) can be played in random order automatically. s Cue and review 1 2 1 2 3 Load a disc and begin playback. Hold down the 2 (2 4) button for audible fast forward, and hold down the 3 (5 3) button for audible fast reverse. Normal playback will resume when the (2 4) button is released. 3 Load a disc(s) and close the disc tray. Press the RANDOM button to begin random play. q "R" will appear. [. . . ] q Load a cassette for recording into the TAPE 2 cassette compartment. q Load the tape with the side to be recorded facing you. Press the TUNER (BAND) or VIDEO/AUX button to select the desired function, and then adjust the sound volume using the VOLUME buttons. VOLUME VIDEO/ AUX TUNING/ TIME ( ) MEMORY/ SET 3 4 Press the TIMER/SLEEP button repeatedly until a red "f" is displayed. q The timer set indicator will flash. W) 5 Press the TUNING/TIME (X or W) button to set the minute start time, then press the MEMORY/SET button. q The unit will enter the stand-by mode automatically, and the timer set indicator will light up. Press the TUNING/TIME (X or button to set the hour start time, then press the MEMORY/SET button. 3 4 6 7 When the preset time is reached, the timer recording will start. [. . . ]