User manual SHARP CMS-N50CDH/CP-N50H

[. . . ] 2 PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 PREPARATION FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8 SETTING THE CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 SOUND CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The station name will flash for 7 seconds, and then remain lit. q If you want to listen to same programmed type of another station, press the PTY. TI SEARCH (PTY. TI) button whilst the channel number or station name is flashing. The unit will look for the next station. Note: q If no station of the programme type you want can be found, "NOT FOUND" will appear for 4 seconds. If you have selected the traffic programme: If you select traffic programme (TP) as the programme type in step 5, to receive only radio stations which broadcast traffic programmes, the TP will appear. (However, this does not necessarily mean that you will hear any traffic announcements at that time. ) When a traffic announcement is actually being made, the TA will appear. (When both the TP and TA will appear, an announcement is being made. ) 1 power on. 2, 3 1 Press the ON/STAND-BY button to turn the 2 Press the TUNER (BAND) button. 3 Press the TUNER (BAND) button to select the FM ST or FM band. 4 Press the PTY. TI SEARCH (PTY. TI) button. q "PTY TI" and "SELECT" will appear alternately for about 6 seconds. 5 Within 6 seconds, press the PRESET (X or W) button to select the programme type you want. DISC TOC TRACK MEMORY RANDOM TOTAL REMAIN kHz REC MHz SLEEP q Each time the button is pressed, the programme type will appear. If the button is held down for more than 0. 5 seconds, the programme type will appear continuously. 23 (Continued) s To manually recall the stations stored in memory When the station you are tuning in is not an RDS station or even if it is an RDS station but it is very weak signal, the display will change in the following order: PRESET(X W) Frequency MHz PRESET(X W) s Notes for Radio text Each time you press the PRESET (X or W) button the channel number will change. q After the channel number has been displayed for 2 seconds, the frequency for that channel will appear for 2 seconds, and then the station name will appear. q The radio text for 10 characters will be displayed steadily for 4 seconds and then it will scroll across the display. This programme carries traffic announcements but none are being broadcast at present and may also carry EON information about other traffic announcements. A traffic announcement is being broadcast on this programme at present. In the following cases, the EON stand-by mode will be cancelled. q Press the ON/STAND-BY button to enter the stand-by mode. q When the unit is switched to another band in the EON stand-by mode q When you change the FM station whilst in the EON stand-by mode q When a preset call is made Notes: q During the same programme as the specified PTY (or TA) is being broadcast on the station you are receiving, the unit will not switch to other network station. q If there are more than two other network stations you want to listen to, compare the strength of each station's signal and tune in the station with the strongest signal. (EON-AF) However, if the frequency of other network station has been stored in the preset channel memory, the unit will switch to that preset channel. q If you want to cancel the reception of an ON (other network) station which was tuned in by the EON system and return to the original station you were receiving, press the EON button. q After the unit returns to the original station, the stand-by mode will still be active. (The "TI" or "PTY" will remain lit. ) q The unit will not switch from the ON station to another network station. The unit returns to the original station. q When the unit switches automatically to "other network" station, if there is any problem with this station or the station cannot be received properly "WEAK SIG" will appear and the unit will return to the original station. [. . . ] Move the write protection tab back to its original position. q Reload the disc or replace it. TEMP OVER TOC ERR* (*:Number or symbol) TOC FULL* (*:Number or symbol) TOC W ERR U TOC ERR* (*:Symbol) U TOC ERR W q Set this unit to the stand-by mode and wait for a while. q Replace it with another disc. q Replace it with another recordable disc. q Recording is impossible. q TOC information recorded on the MD does not match the MD specifications or it cannot be read. [. . . ]