User manual SHARP CMS-R160CDH/CDG

[. . . ] CD-BA250H/CD-BA2600H mini systeem bestaande uit CD-BA250H/CD-BA2600H (hoofdtoestel) en CP-BA250H/CP-BA2600H (luidsprekersysteem). CD-BA250H/CD-BA2600H Mini Component System consisting of CD-BA250H/CDBA2600H (main unit) and CP-BA250H/CP-BA2600H (speaker system). CD-BA250H CD-BA2600H BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUAL DE MANEJO BRUKSANVISNING MANUALE DI ISTRUZIONI GEBRUIKSAANWIJZING OPERATION MANUAL DEUTSCH FRANÇAIS ESPAÑOL SVENSKA ITALIANO NEDERLANDS ENGLISH Siehe Seiten i bis v und D-1 bis D-35. Se reporter aux pages i à v et F-1 à F-35. Consulte las páginas i al v y S-1 al S-35. [. . . ] Then, press the DISC SKIP button to rotate the disc tray and remove the remaining disc. After use: Press the ON/STAND-BY button to enter the power stand-by mode. For audible fast reverse: Press and hold down the PRESET button during playback. Caution: z z z z z Do not place two CDs in one disc tray. Do not push the disc tray whilst it is moving. If the power fails whilst the tray is open, wait until the power is restored. If the disc tray is stopped forcibly, "ER-CD10" will appear in the display and the unit will not function. If this occurs, press the ON/STAND-BY button to enter the power stand-by mode and then turn the power on again. z If TV or radio interference occurs during CD operation, move the unit away from the TV or radio. z If a disc is damaged, dirty, or loaded upside down, the disc will be skipped. Notes: z Normal playback will resume when the PRESET or PRESET button is released. z You can locate the desired portion on a single disc only. z When the end of the last track is reached during fast forward, "END" will appear on the display and CD operation will be paused. When the beginning of the first track is reached during fast reverse, the unit will enter the playback mode. z The / or / button on the remote control allows you to locate the desired portion. ENGLISH E-13 CD Playback Notes: - Listening to a CD (CDs) - z Playback will begin from track 1 on the disc you have selected to play. z Auto scan tuning will skip weak signal stations. z To stop the auto tuning, press the TUNING/TIME button again. z When an RDS (Radio Data System) station is tuned in, the frequency will be displayed first, and then the RDS indicator will light. z Full auto tuning can be achieved for RDS stations "ASPM", see page 20. To receive an FM stereo transmission: Press the TUNER (BAND) button to display the "ST" indicator. z " " will appear when an FM broadcast is in stereo. FM stereo mode indicator FM stereo receiving indicator z If the FM reception is weak, press the TUNER (BAND) button to extinguish the "ST" indicator. The reception changes to monaural, and the sound becomes clearer. After use: Press the ON/STAND-BY button to enter the power stand-by mode. E-16 ENGLISH Sound Control (See page 10. ) Listening to the Memorised Station , , Memorising a station You can store 40 AM and FM stations in memory and recall them at the push of a button. (Preset tuning) , , To recall a memorised station Press the PRESET or PRESET 0. 5 seconds to select the desired station. button for less than 1 2 Perform the steps 1 - 3 in "Listening to the Radio" on page 16. Press the MEMORY/SET button to enter the preset tuning saving mode. 3 Within 30 seconds, press the PRESET button to select the preset channel number. or PRESET , , To scan the preset stations The stations saved in memory can be scanned automatically. (Preset memory scan) 1 Store the stations in memory, in order, starting with preset channel 1. Press the PRESET than 0. 5 seconds. or PRESET button for more 4 Within 30 seconds, press the MEMORY/SET button to store that station in memory. z The preset number will flash and the programmed stations will be tuned in sequentially, for 5 seconds each. [. . . ] z Are the speaker wires disconnected? , , Remote control Symptom Possible cause z The remote control does not oper- z Is the AC power lead of the unit plugged ate. z Does the remote control sensor receive strong light? , , CD player Symptom Possible cause z Playback does not start. z Playback stops in the middle or is z Does the disc satisfy the standards?z Playback sounds are skipped, or z Is the unit located near excessive vibrastopped in the middle of a track. [. . . ]