User manual SHARP CMS-R70CDH/CP-R70

[. . . ] q The AC adaptor may be different from the one in the drawing. 2 Web-site: www. sharp. co. uk/support Help Line: 0990 274277 (office hours) Contents Important Introduction Special Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Names of Controls and Indicators . . . . . . . . . . . . . . 6-7 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Hold Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] q When the battery has run completely out, "BATT EMPTY (LoBATT)" will appear. Then, the power will be disconnected automatically. Notes: q If you use the battery which you stopped charging half" may appear. It does not mean that the batway, " tery is completely charged. q The battery indicator will not correctly display the remaining capacity for approximately 10 seconds after the power has been turned on. q When the AC adaptor or a separately available car adaptor is used, the battery indicator will not be shown. q The number of bars shown in the battery indicator may increase or decrease, depending on the operation being performed. Help Line: 0990 274277 (office hours) Web-site: www. sharp. co. uk/support 29 ­ Checking Displays ­ 1 Whilst in the stop mode, press the 5 or 4 button to display the track number and track name. Useful Features The remaining amount of battery level is shown by the battery indicator ( ) during operation. Battery Power Charging the rechargeable battery 1 Useful Features When the rechargeable battery is used for the first time or when you use it after a long period of disuse, be sure to charge it fully. ­ Battery Power ­ 2 1 2 3 Slide the battery cover as far as it will go to the outside. Lift the battery cover. q Do not force the battery cover open too far. Insert the rechargeable battery from the (+) marked side. q A rechargeable battery other than the one sup- plied or the separately available one (AD-N70BT) cannot be charged. 4 5 To the DC IN 5V socket To wall socket AC 230-240V, 50/60 Hz Close the battery cover. Plug the AC adaptor into the wall socket, and then insert the plug on the other end into the DC IN 5V socket. Press the :OFF/CHRG (·s ) button. q" 6 " will flash, and battery will begin charging. q The recording will be made in the analogue mode. q Character information will not be recorded. Notes: q Adjust the volume of both this unit and a car stereo. q Do not operate this unit whilst you drive a car. It may distract your attention and cause a traffic accident. q Do not use any car adaptor except for the separately available AD-CA20X. q Remove the battery when you power the unit from the car battery. Web-site: www. sharp. co. uk/support Help Line: 0990 274277 (office hours) 32 Changing Default Settings Beep sound You can eliminate the confirmation sound that beeps when you press a button. Whilst in the stop mode . . . Advanced Features Auto play You can make the unit not play automatically when you insert a playback-only MiniDisc or an accidental erasure protected MiniDisc. q When you release the button, "BEEP ON (BEEP 1)" or "BEEP OFF (BEEP 0)" will appear. Auto power save When the unit is used in a place exposed to much vibration, sound skipping can be decreased by cancelling the auto power save function. (Battery will drain faster. ) What is auto power save function? Auto power save function automatically adjusts the sound skip memory storage to be from 5 to10 seconds depending on playback conditions, this saves battery power. If the MiniDisc unit is used in areas of much vibration it may be necessary to fix the sound skip memory to 10 seconds "Psave OFF (PS off)" this will improve performance under difficult conditions but uses more power. (When the AC/car adaptor is used the 10 second mode is always used) 2 Press the 5 or 4 button to display the menu. Then press the MODE button to switch items. [BEEP ON] (BEEP 1) Beep sound [BEEP ON] (*) (BEEP 1) [A-PLAY ON] (autoPL) Auto play [A-PLAY ON] (*) (autoPL) [AUTO Psave] (autoPS) Auto power save [AUTO Psave] (*) (autoPS) [BEEP OFF] (BEEP 0) [A-PLAY OFF] (PL off) [Psave OFF] (PS off) (*) indicates default setting. 3 Press the · s/:OFF button. Help Line: 0990 274277 (office hours) Web-site: www. sharp. co. uk/support 33 ­ Changing Default Settings ­ 1 With a MiniDisc inserted, press the MODE button for 2 seconds or more. "SET UP" will appear. Titling a MiniDisc Creating disc and track names Advanced Features One disc name and up to 255 track names can be created per disc (A maximum of 100 characters for the disc and each track name and a total of 1, 700 characters can be entered). 4 Press the 5 or 4 button repeatedly to select the letter. ­ Titling a MiniDisc ­ 1 Disc name Whilst in the pause mode, press the EDIT button repeatedly to select "DISC NAME". Track name Whilst in the pause mode, press the EDIT button repeatedly to select "TRACK NAME". 5 Press the ENTER/SYNC button to enter it. Position where the next letter will be entered 2 Press the ENTER/SYNC button. Cursor q The unit will enter the character input mode. [. . . ] 19 To play at double speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Function Battery level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Battery power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]