User manual SHARP CP-XL12

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: q Reorient or relocate the receiving antenna. [. . . ] The entire MiniDisc is controlled depending on this TOC, which enables the unit to find the beginning of a track quickly or to automatically record in a vacant area. Recordings cannot be made in the following situations. q If you try recording on a playback-only MiniDisc (commercially available music MiniDisc). q If a MiniDisc is protected against accidental erasure (page 36). q If there is no more recording time left on the disc (page 37). q When the "TOC FULL" message appears (page 39). q If a disc's TOC has been damaged. Notes: q When recording important selections, be sure to make a preliminary test to ensure that the desired material is being properly recorded. q The VOLUME, X-BASS, EQUALIZER and SURROUND controls can be adjusted during recording, with no effect on the recorded signal. Area for TOC (recording track numbers, track names, etc. ) Area for recording the sound When you start recording or editing, "TOC" will appear in the display window. This indicates that information in the TOC is now being changed according to the recording or editing being performed. (The changed TOC is not yet recorded on the MiniDisc at this time. ) The TOC is recorded when q you stop recording. Do NOT unplug the power cord while the TOC is being recorded ("TOC" is flashing) and do NOT impart shock to the unit. Otherwise, TOC will not be correctly recorded, and consequently proper playback may not be possible. 21 (Continued) s Recording from a CD onto a MiniDisc (One-Touch Editing) A CD can be recorded to a MiniDisc, starting from the first track, with one-touch operation. To cancel the operation: Before pressing the CD 0 MD EDIT (HIGH or NORMAL) button, press the CD s button. To stop recording: Press the MD s button. 3 Press the CD 0 MD EDIT (HIGH or NORMAL) button. q APMS playback will start, and recording will start automatically. q Programmed tracks will be recorded in order. After the unit has finished recording the last track, recording will stop automatically. Note: q If repeat play has been set, when you press the CD 0 MD EDIT (HIGH or NORMAL) button, the repeat mode will be canceled automatically, and APMS recording will start. MD H 3 2 To stop recording: Press the MD s button. q Playback and recording will stop and the track numbers will be written on the MiniDisc. 1 Load a CD and a recordable MiniDisc. 2 Press the q REC button. q The unit will enter the recording stand-by mode. 3 Press the CD 06 button. To stop recording: Press the MD s button. q Recording will stop and the track numbers will be written on the MiniDisc. 24 (Continued) s Recording from the built-in radio onto a MiniDisc MD s To stop recording: Press the MD s button. The recording will stop and the track number will be written on the MiniDisc. 5 To record the track number while recording: The recording is performed as a single track. To identify different sections of a recording, you can increase the track number at any point during the recording process. To create a new track number while in the recording mode, press the q REC button. q The track number will increase by one, and then the recording will continue. 2 4 3 5 MD s 4 3 1 Tune in to the desired station (pages 19 - 20). [. . . ] Contact your local CD software dealer for options. SPECIFICATIONS As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. q General Power source: Power consumption: Dimensions: AC 120 V, 60 Hz 51W Width; 8-1/2" (215 mm) Height; 6-7/16" (162 mm) Depth; 13-1/2" (342 mm) 9. 7 Ibs. (4. 4 kg) q Compact disc player section Type: Signal readout: Rotation speed: Error correction: Quantization: Drawer type compact disc player Non-contact, 3-beam semiconductor laser pickup 200 - 500 rpm CLV, Approx. [. . . ]