Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SHARP ER-A170. We hope that this SHARP ER-A170 user guide will be useful to you.
Lastmanuals help download the user guide SHARP ER-A170.
Detailed instructions for use are in the User's Guide.
[. . . ] AVISO: El tomacorriente debe estar instalado cerca del equipo y debe quedar bien accesible. VARNING: Det matande vägguttaget skall placeras nära apparaten och vara lätt atkomligt. CAUTION: For a complete electrical disconnection pull out the mains plug. VORSICHT: Zur vollständigen elektrischen Trennung vom Netz den Netzstecker ziehen. [. . . ] (Reserved) EFT error EFT connection is broken. (Reserved) Closing the drawer is compulsory. (Reserved) Entry of secret code is needed. (Reserved) Data backup send success Data backup receive success Data backup communication error Backup data format error Data backup time out error (Reserved) EURO change compulsory In default of programming INH. UNIT PR NOT NON-TEND
BUFFER FULL EFT ERROR EFT BREAK CLOSE DRAWER ENTR SECRET# SEND OK RECEIVE OK COM. ERROR DATA ERROR TIME OUT EURO CHANGE
74
FOR THE MANAGER-2-A410/A420
02. 4. 20 6:49 PM
Page 75
Programming of texts of validation printing
PGM 2
2642
You can program the texts (3 lines) to be printed on validation slip. Up to 24 characters can be programmed per line.
Procedure
To keep the current setting 2642
.
No. of lines (1 - 3)
Character keys (max. 24 digits)
:
;
Example
Key operation
Print
2642 . 3 FOR / DEPOSIT / ONLY :
;
Programming of texts of slip printing
Procedure
PGM 2
2643
You can program the texts (3 lines) to be printed on slip. Up to 24 characters can be programmed per line.
To keep the current setting 2643
.
Line no. Always enter 0.
** P: 2 (ABCD: Always enter 0. ) ** P: 3
*
Item: A B
Selection: Always enter 0. for the slip printer Not connected Standard channel 1 Standard channel 2
C D
Always enter 0. Always enter 0.
Entry: 0 0 1 2 0 0
Note
· Never enter any number other than 0, 1 and 2. · EFT function always uses standard channel 2. · Data backup function always uses standard channel 1.
Example
Key operation
Print
2690 . 3 0100 :
;
81
FOR THE MANAGER-2-A410/A420
02. 4. 20 6:49 PM
Page 82
Programming of RS-232C interface
6220
PGM 2
6110
6111
6112
6113
6115
Terminal number
Procedure
To program zero 6110
.
Terminal no. 6 digits)
;
Transmission line form
Procedure
To program zero 6111
.
Line form
* AB
;
Selection: No Sensing Full duplex system Half duplex system Entry: 0 1 0 1
*
Item: A B
Sensing of the CI signal
Functional programming
Procedure
To program zero 6112
.
* AB
;
Selection: Data sending and receiving Print data sending 4800 bps 9600 bps 19200 bps 38400 bps Entry: 0 1 4 5 6 7
*
Item: A B
Selection of print data sending/data sending and receiving Baud rate (38400/19200/9600/4800 bps) The selected baud rate is used for on-line communications and print data sending. It is not used for the data backup function.
Start code and end code
Procedure
To program zero 6113
.
* ABCDEF
;
* ABC: Start code (000 127) DEF: End code (000 127)
Time out time
Procedure
6115
82
.
Time out time (1 255 sec)
;
FOR THE MANAGER-2-A410/A420
02. 4. 20 6:49 PM
Page 83
Programming for print data sending
Procedure
To program zero 6220
.
* ABC
;
Selection: Yes No Yes No Disable Enable Entry: 0 1 0 1 0 1
*
Item: A B C
Sensing of DR signal Sensing of CS signal Sending of all print data
Secret codes to control access to PGM1 mode, X1/Z1 mode and X2/Z2 2631 2632 mode PGM 2 2630
You must enter a secret code according to the following procedure before performing any PGM1-mode, X1/Z1mode or X2/Z2-mode operation when a secret code has been set for that specific mode operation. Operating
Procedure
;
Note
Secret code Max. 4 digits
;
Once a secret code is entered, it does not need to be entered again unless the mode switch setting is changed and any operation is performed.
Programming
Procedure
* 2630 2631 2632 No code (zero)
.
Secret code Max. 4 digits
;
* 2630 for the PGM1 mode 2631 for the X1/Z1 mode 2632 for the X2/Z2 mode
Example
Key operation
Print
2631 . [. . . ] The direct non-tendering finalization after previous tender entry is inhibited. (Reserved) EFT error EFT connection is broken. (Reserved) Closing the drawer is compulsory. (Reserved) Entry of secret code is needed. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP ER-A170
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP ER-A170 will begin.