User manual SHARP ER-4100S

[. . . ] This copier can be used as a laser printer and as a facsimile machine by installing optional components. However, this manual describes only the copier features. For description of the printer features and facsimile features, see their separate manuals. 1 Getting started Conventions used in this manual In this manual, the following icons are used to provide the user with information pertinent to the use of the copier. Warns the user that injury to the user or damage to the copier may result if the contents of the warning are not properly followed. Cautions the user that damage to the copier or one of its components may result if the contents of the caution are not properly followed. Notes provide information relevant to the copier regarding specifications, functions, performance, operation and such, that may be useful to the user. Indicates a letter displayed in the display. 3 CAUTIONS Follow the cautions below when using this copier. q The fusing area is hot. Exercise care in this area when removing misfed paper. [. . . ] When the SPF misfeeds an original sheet, the copier will stop and the SPF misfeed ( ) indicator will blink, while the misfeed ( ) indicator will remain off. For a misfeed of originals in the SPF, see page 38. Ensure that the bypass tray is open and then open the side cover while pressing the side cover open button. 5 Copier trouble? Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If blinks in the display, proceed to "A Misfeed in the paper feed area". 27) If paper is misfed here, proceed to "B Misfeed in the fusing area". 27) If the misfed paper is seen from this side, proceed to "C Misfeed in the transport area". 28) If paper is misfed here, proceed to "A Misfeed in the paper feed area". 27) 26 MISFEED REMOVAL A Misfeed in the paper feed area Gently remove the misfed paper from the paper feed area as shown in the illustration. When blinks in the display and the misfed paper is not seen from the paper feed area, pull out the paper tray and remove the misfed paper. If the paper cannot be removed, proceed to "B Misfeed in the fusing area". Gently close the front cover and then close the side cover. Place the original face down on the original table. Press any key to cancel the preheat mode. Press the print ( ) key to cancel the auto power shut-off mode. If using special papers, feed the paper through the bypass tray. Store copy paper flat in the wrapper in a dry location. Set the guides properly depending on the paper size. Use copy paper within the specified range. If the copier is not used for a long time, remove the paper from the paper tray and store it in its wrapper in a dry location. Copier does not operate. Power switch on?Is the original placed face down on the original table?Is the copier in the auto power shut-off mode? Blank copies 19 19 15 32 Power save ( indicator on. ) 5 Copier trouble? Is original image too dark or too light? [. . . ] Eye; In case of contact, immediately flush eyes with water for 15 minutes. Route(s) of Entry: Section 6. Physical Chemical Characteristics Not applicable Not applicable Not applicable Not applicable Fine powder Odorless Specific Gravity: Solubility in Water: PH: Viscosity: Color: about 7. 3 Negligible Not applicable Not applicable Black Boiling / Melting Point: Vapor Pressure: Vapor Density: Evaporation Rate: Appearance: Odor: Section 7. Fire and Explosion Data Not applicable >350°C (LEL); Not applicable (UEL); Not applicable CO2, dry chemical, foam or water None This material has no unusual fire or explosion hazards. None None Flash Point (Method Used): Ignition Temperature: Flammable Limits: Extinguishing Media: Special Fire Fighting Procedure: Unusual Fire and Explosion Hazard: Sensitivity to Mechanical Impact: Sensitivity to Static Charge: Section 8. Reactivity Data Stable None CO and NOx Will not occur. Stability: Incompatibility (Material to Avoid): Hazardous Decomposition: Hazardous Polymerization: Section 9. Precautions for Safe Handling and Use Personal Protection Information (Respiratory, Eye Protection and Protective Glove): None required under normal use. Engineering Control / Ventilation: Not required. Steps to be taken in case of Spill or Leak: Sweep up or clean up with vacuum cleaner. [. . . ]