User manual SHARP FO-775L

[. . . ] MODEL FO-775L FACSIMILE OPERATION MANUAL 1. 11. Installation Setting Up and Using OpenLCR Sending Documents Receiving Documents Making Copies Making Telephone Calls Answering Machine Hookup Special Functions Printing Lists Maintenance Troubleshooting open LCR www. OpenLCR. com WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Answering Machine Hookup Connecting an Answering Machine If desired, you can connect an answering machine to your fax machine's TEL. This will allow you to receive both voice messages and faxes when you are out. 1 Remove the seal covering the TEL. SET jack. 2 Connect the answering machine's telephone line jack to the TEL. · If desired, you can connect an extension phone to your answering machine's extension phone jack. TEL. LINE jack is connected to the wall jack. To answering machine's telephone line jack. 88 Connecting an Answering Machine Changing the outgoing message The outgoing message (OGM) of your answering machine should be changed to inform callers who want to send a fax to press their Start key. For example, your message might go as follows: "Hello. No one is available to take your call right now. Please leave a message after the beep or press your facsimile Start key to send a fax. Thank you for calling. " Try to keep the length of the message under 10 seconds. If it is too long, you may have difficulty receiving faxes sent by automatic dialing. If your outgoing message must be longer than 10 seconds, leave a pause of about four seconds at the beginning of the message. This will give your fax a chance to detect fax tones sent when automatic dialing is used. Activating the answering machine connection Before you go out, activate the answering machine connection as follows: 1 Set the reception mode to A. M. RECEPTION MODE TEL FAX A. M. 89 7. Answering Machine Connecting an Answering Machine 2 Set your answering machine to auto answer. Your answering machine must be set to answer on a maximum of two rings. If not, you may not be able to receive faxes sent by automatic dialing. If your answering machine has a toll saver function, make sure that it will answer by the fourth ring. Note: If your answering machine has a remote retrieval function, make sure the code used to activate remote retrieval is different from the code used to activate fax reception with an extension telephone (see page 76). If they are the same, entering the code from an outside telephone to retrieve messages will cause the fax machine to be activated. How the connection operates While you are out, all of your incoming calls will be answered by your answering machine and its outgoing message will play. During this time, your fax will quietly monitor the line. If your fax detects a fax tone or a duration of silence greater than four seconds, it will take over the line and begin reception. When you return and turn off your answering machine, be sure to change the reception mode back to FAX or TEL! 90 Optional A. M. Mode Settings If necessary, you can use the following settings to improve the response of the answering machine hookup to incoming calls. Quiet Detect Time The fax machine is set to take over the line and begin reception if it detects 4 seconds of silence after the answering machine answers. [. . . ] Physical Chemical Characteristics Boiling/Melting Point Vapor Pressure Vapor Density Evaporation Rate Appearance Odor m. p. about 70 C for ink Not applicable Not applicable Negligible Thin film coated with ink Slight wax odor Specific Gravity Solubility in Water PH Viscosity Color about 1 Negligible Not applicable Not applicable Black Section 7. Fire and Explosion Data Flash Point (Method Used) Ignition Temperature Flammable Limits Extinguishing Media Special Fire Fighting Procedure Unusual Fire and Explosion Hazard Sensitivity to Mechanical Impact Sensitivity to Static Charge : about 250°C for ink :Not applicable : (LEL): Not applicable(UEL): Not applicable : CO2, water , dry chemicals and form etc. : None : None : No hazardous effect by mechanical impact : Not applicable : : : : Stable None Not applicable Not applicable Section 8. [. . . ]