User manual SHARP FU-60SE-K

[. . . ] R FU-60SE-K AIR PURIFIER OPERATION MANUAL Floor / Tabletop type "Plasmacluster" is trademark of Sharp Corporation. NEDERLANDS ITALIANO ESPAÑOL TERMS OF GUARANTEE Sharp Electronics (UK) Ltd. ("Sharp") guarantees to provide for the repair, or at its option the replacement, of this product subject to the conditions listed below:1. This guarantee shall only apply to faults which are due to inferior workmanship or materials. It does not cover faults or damage caused by accident, misuse, fair wear and tear, neglect, tampering with the product, or repair other than by a Service Facility appointed by Sharp. [. . . ] In this case, move away from such lighting equipment or change direction. · Location exposed to direct sunlight The unit may not receive signals from the remote control. The unit may not respond to the signals of the remote control if the ends of fluorescent lighting become black or lights flicker due the depletion of service life; however, this is not a malfunction of the remote control or the main unit. In this case, replace the lighting with new fluorescent tubes. TAKE CAUTION TO THE FOLLOWING DURING INSTALLATION · Leave at least 2m of space from televisions, radios and wave clocks. Electrical interference may occur if not. · Leave at least 60cm of space from the wall The motor may overheat, causing malfunction if not. · Avoid a location where sensors are exposed to direct wind The unit may not operate properly. · Avoid a location where curtains, etc. , come into contact with the intake or Air Outlet. Curtains, etc. , may become dirty or malfunction may occur as a result. EFFECTIVE OPERATION · Place on a stable surface with sufficient air circulation ABOUT THE FILTER · Do not wash and reuse HEPA filter and Active carbon filter. They do not effect, and may become a cause of electric shock and trouble. · The wall, etc. , behind the Air Outlet may become dirty as time passes. When using the unit for extensive period in the same location, use a vinyl sheet, etc. , to prevent the wall from becoming dirty. In addition, periodically clean the wall, etc. E-3 NAMES OF PARTS MAIN UNIT DISPLAY OFF timer display lamps (set using remote control) AUTO operation lamp Fan level lamps Filter lamp If the Filter lamp is lit, the Active carbon filter needs to be cleaned. CLUSTER ION LAMP Cluster ion operation is selected using the remote control. Blue light When the cluster ion operation is in Clean mode or AUTO cluster ion mode and the air in the room is dirty, this light turns on and the unit will operate in Clean mode. Green light When the cluster ion operation is in Ion control mode or AUTO cluster ion mode and the air in the room is clean, this light turns on and the unit will operate in Ion control mode. Light off No cluster ions are generated. · The light can be turned off by using the `DISPLAY ON/OFF button' on the remote control even while cluster ions are generated (Please turn off the lights when not required. ) EXPLODED DIAGRAM E-4 Pollen mode operation lamp CLEAN-SIGN The color changes when the air is dirty. Clean (green) Slightly dirty (orange) Very dirty (red) ABOUT THE CLEAN-SIGN · The sensor displays a CLEAN-SIGN lamp depending on relative changes to the environment from the time the power plug is inserted into the wall outlet and thereafter. · When the air is extremely dirty at the time the power plug is inserted, the CLEAN-SIGN lamp may light green since the polluted state is the environment against which the sensor bases the pollution rate on. In this case, switch manually to the desired operation mode as it is ineffective in auto operation. See Page E-11 · The CLEAN-SIGN lamp can be turned off using the "DISPLAY ON/ OFF" button of the remote control. See Page E-11 Remote control receiver MODE/ button See Page E-10 (Used to select operation modes or turn the unit off) Sensor sensitivity select switch The sensitivity of odor and dust detection can be adjusted. This setting is factory set to "Normal". Set the sensitivity to "High" if the sensitivity seems too low depending on the room condition. Filter reset button Odor sensor Detects odors such as tobacco smoke, incense, pets, cosmetics, etc. *Before pressing the Filter reset button, be sure to connect the power plug to a wall outlet. [. . . ] HEPA filter materials: Active carbon filter materials: · Filter: Polypropylene · Deodorizer: Activated charcoal · Frame: Polyester · Net: Polypropylene 60% Polyester 40% E-14 TROUBLESHOOTING Before calling for repair, check the symptoms below for possible remedies, since the problem may not be a malfunction of the unit. SYMPTOM The remote control does not work REMEDY (not a malfunction) · Have the batteries been depleted?· Are the batteries inserted correctly?· Is a fluorescent lighting in the room flickering due to service life?(Refer to E-3, E-7) · Are the filters heavily soiled? [. . . ]