User manual SHARP GF-8H

[. . . ] Depending on the usage environment, especially when the product is used in extreme environments (significantly more severe than normal household use), this odour may become strong in a shorter period than expected. If the odour persists, the filters should be replaced. NOTE · The air purifier is designed to remove air-suspended dust and odour, but not harmful gases (for example, carbon monoxide contained in cigarette smoke). If the source of the odour still exists, the air purifier may not completely remove the odour. HEPA Filter Washable Deodorizing Filter Pre-Filter (Common illustration has used "KC-850E". ) KC-840E_Eng2. indd 2 08. 10. 10 9:23:04 AM ENGLISH FEATURES Unique Combination of Air Treatment Technologies Triple Filtration System + Plasmacluster + Humidification TRAPS DUST* Washable pre-filter traps dust and other large airborne particles. DECREASES ODOURS Washable deodorizing filter absorbs many common household odours. [. . . ] HEPA Filter Tab Back Panel 2 2 Remove the Washable Deodorizing Filter (black) and HEPA Filter (white) from the plastic bags. Insert the Back Panel's 2 bottom tabs (left and right) into the small holes in the unit, and slide the Washable Deodorizing Filter between the HEPA Filter and the Back Panel. Washable Deodorizing Filter Back Panel Bottom tabs 3 HEPA Filter Gently push in the upper tabs (left and right) to lock in place. Upper tabs Washable Deodorizing Filter 4 Fill in the usage start date on the Date Label. Use the usage start date as a guide for when the filters should be replaced. Date Label E-6 KC-840E_Eng2. indd 6 08. 10. 10 9:23:25 AM REFILLING THE WATER TANK The unit can be used in the Clean Air Mode without putting water in the Water Tank. In such cases, it is recommended that CLEAN AIR & HUMIDIFY/MAX MODE be used. Temperature ~18 ºC 18 ºC~24 ºC 24 ºC~ Humidity 65 % 60 % 55 % E-8 KC-840E_Eng2. indd 8 08. 10. 10 9:23:26 AM CLEAN AIR MODE Use the Clean Air Mode when additional humidity is not required. 1 2 · If the power cord was not unplugged between uses, the unit will automatically re-start at the previously selected settings. Press the CLEAN AIR MODE Button on the display. Press the Power OFF Button to turn the unit off. CLEAN ION SHOWER MODE CLEAN ION SHOWER Mode with humidification releases high-density Plasmacluster ions. By continuously discharging strong airflow for 15 minitues, the unit effectively removes airborne dust, pollen, mold and allergens from the air as they are drawn through the filter system. Water must be in the Water Tank when this mode is selected. The unit humidifies when there's water in the Water Tank, and it operates without humidifying when there's no water in it. When the operation finishes, the unit will return to the prior operation. Press the Power OFF Button to turn the unit off. Fan Speed Button AUTO operation POLLEN operation MAX operation MEDIUM operation LOW operation mode Please note the fan speed cannot be adjusted during the CLEAN ION SHOWER MODE. The fan speed is automatically switched (between HIGH and LOW) depending on the amount of impurities in the air. The sensors detect impurities for efficient air purfication. The unit will operate at High Level for 10 minutes, then will atternate between MEDIUM and HIGH. The unit will operate at maximum fan speed. The unit will operate at medium fan speed. The unit will operate quietly using minimal air intake. *HiGH fan speed is an intermediate speed between MEDIUM and MAX. Detergent ingredients may damage the unit. E- KC-840E_Eng2. indd 11 Remove the sensor filter and tap it lightly over a sink or bin to dislodge dust. If it is very dirty, wash it gently with lukewarm water. Do not use any detergents or chemicals of any kind to clean the filter. Dry the filter completely before replacing in the unit. Do not operate unit without all filters properly installed. Sensor Filter NEDERLANDS 1 2 3 In case of oily dirt, soak the back panel in water with kitchen detergent. Avoid scrubbing the back panel hard when washing. Rinse the back panel repeatedly with clean water to remove the solution residue. Back Panel FRANÇAIS Whenever dust accumulates on the unit or every 2 months Gently remove dust from the sensor opening and the back panel, using a vacuum cleaner attachment or similar tool. Care Cycle Sensor Back Panel DEUTSCH BACK PANEL and SENSORS CARE AND MAINTENANCE WATER TANK Care Cycle Every day when Humidifying Tank Cap Water Tank Rinse the inside of the tank by leaving a small amount of lukewarm water inside, closing the tank cap firmly, and shaking the tank. Mild household detergents may be used to clean the inside of the tank, but detergent should be diluted and the tank should be thoroughly rinsed to remove all detergent residue. (Note the Water Tank is not dishwasher safe. ) TANK CAP CARE care cycle. . . once a month Tank Cap The small cap back of the tank cap is removable. When the tank cap and small cap are dirty and slimy, cleaning is necessary. [. . . ] · Check to see if the filters are heavily soiled. · Plasmacluster Air Purifiers emit small traces of ozone which may produce an odour. · Is the unit installed in a location that is difficult for the sensor to detect cigarette smoke?· Are the dust sensor openings blocked or clogged? [. . . ]