User manual SHARP GS-XP24ER

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SHARP GS-XP24ER. We hope that this SHARP GS-XP24ER user guide will be useful to you.

Lastmanuals help download the user guide SHARP GS-XP24ER.


Mode d'emploi SHARP GS-XP24ER
Download
Manual abstract: user guide SHARP GS-XP24ER

Detailed instructions for use are in the User's Guide.

[. . . ] R Air Conditioner GS-XP07ER GS-XP09ER GS-XP12ER GS-XP18ER GS-XP24ER GS-XP27ER AR CONDICIONADO DE DUAS UNIDADES MANUAL DE INSTRUÇÕES · Uses ozone layer friendly refrigerant R410A. · Utiliza refrigerante R410A que no daña la capa de ozono. · Utilizza il refrigerante R410A che non danneggia il buco nell'ozono. · Usa refrigerante R410A amigo da camada de ozono. [. . . ] During de-icing, the inside and outside fans stop operating. · After de-icing is completed, the unit automatically resumes operation in the HEAT mode. HEATING EFFICIENCY · The unit employs a heat pump that draws heat from the outside air and releases it into the room. The outside air temperature therefore greatly affects the heating efficiency. · If the heating efficiency is reduced due to low outside temperatures, use an additional heater. · It takes time to warm up and heat the entire room because of the forced air circulation system. TIPS ON SAVING ENERGY Below are some simple ways to save energy when you use your air conditioner. SET THE CORRECT TEMPERATURE · Setting the thermostat 1°C higher than the desired temperature in the COOL mode and 2°C lower in the HEAT mode will save approximately 10 percent in power consumption. · Setting the temperature lower than necessary during cooling operation will result in increased power consumption. BLOCK DIRECT SUNLIGHT AND PREVENT DRAFTS · Blocking direct sunlight during cooling operation will reduce power consumption. · Close the windows and doors during cooling and heating operations. SET PROPER AIR FLOW DIRECTION TO OBTAIN THE BEST AIR CIRCULATION KEEP FILTER CLEAN TO ENSURE THE MOST EFFICIENT OPERATION MAKE MOST OF THE TIMER OFF FUNCTION DISCONNECT THE POWER CORD WHEN THE UNIT IS NOT USED FOR AN EXTENDED PERIOD OF TIME · The indoor unit still consumes a small amount of power when it is not operating. E-3 PART NAMES INDOOR UNIT (When installed on the floor) 1 Outlet (Air) 2 Vertical Adjustment Louvres 1 2 3 4 3 Horizontal Adjustment Louvres 4 Indicator Panel 5 Inlet (Air) 6 Air Filters 7 Intake Grill 8 Remote Control 9 OPERATION Lamp (red 0 TIMER Lamp (orange 5 6 7 ) q PLASMACLUSTER Lamp (blue, green) w RECEIVER Window e AUX. Button (When installed on the ceiling) 8 9 0 q ) w AUX. e r Inlet (Air) t Interconnecting Cord and Refrigerant Tube y Drainage Hose GU-XR18ER u Outlet (Air) GU-XR24ER GU-XR27ER OUTDOOR UNIT GU-XR07ER GU-XR09ER GU-XR12ER r t y r t y u u NOTE: Actual units might vary slightly from those shown above. E-4 REMOTE CONTROL 1 1 TRANSMITTER 2 DISPLAY (Liquid Crystal Display) 3 PLASMACLUSTER Button 4 ON/OFF Button 2 5 THERMO. (Thermostat) Button 6 FULL POWER Button 7 MODE Button 3 4 5 6 7 8 9 0 q w e r t y u 8 ONE-HOUR OFF TIMER Button 9 TIMER ON Button (for setting the timer) 0 TIMER OFF Button (for setting the timer) q TIME ADVANCE Button w TIME REVERSE Button e FAN Button r TIMER SET/CANCEL Button t Indicates BATTERY COMPARTMENT is below this mark y CLOCK Button u SWING Button ENGLISH MODE 1h FAN SWING SET/C L. C. D. REMOTE CONTROL DISPLAY i PLASMACLUSTER SYMBOL o MODE SYMBOLS : AUTO : HEAT : COOL : DRY i o p a s d f p THERMOSTAT SETTING FOR AUTO AND DRY MODES a TEMPERATURE INDICATOR s TRANSMITTING SYMBOL d FULL POWER SYMBOL f FAN SPEED SYMBOLS : AUTO : HIGH : LOW : SOFT g h g TIMER ON INDICATOR/CLOCK Indicates the on timer preset time or current time. h TIMER OFF INDICATOR Indicates the preset time for off timer or onehour off timer. E-5 USING THE REMOTE CONTROL LOADING BATTERIES Use two size-AAA (R03) batteries. 1 Remove cover. the remote control Remote control cover batteries in 2 Insert making surethe compartment, the ± and -- polarities are correctly aligned. · The display indicates "AM 6:00" when batteries are properly installed. the cover. 3 Reinstall NOTES: + + · The battery life is approximately one year in normal use. · When you replace the batteries, always change both batteries, and make sure they are the same type. · If the remote control does not operate properly after replacing the batteries, take out the batteries and reinstall them again after 30 seconds. · If you will not be using the unit for a long time, remove the batteries from the remote control. HOW TO USE THE REMOTE CONTROL Point the remote control towards the unit's signal receiver window and press the desired button. The unit generates a beep when it receives the signal. · Make sure there is no curtain or other object between the remote control and the unit. · The remote control can send signals from up to 7 metres away. Ceiling suspended Floor standing E-6 CAUTION · Do not allow the signal receiver window to receive strong direct sunlight, since it can adversely affect its operation. If the signal receiver window is exposed to direct sunlight, close a curtain to block the light. · Using a fluorescent lamp with a quick starter in the same room may interfere with transmission of the signal. · The unit can be affected by signals transmitted from the remote control of a television, VCR or other equipment used in the same room. · Do not leave the remote control in direct sunlight or near a heater. [. . . ] · Do not directly splash or pour water on them. We can cause electrical shock or equipment damage. · Do not use hot water, thinner, abrasive powders or strong solvents. MAINTENANCE AFTER AIR CONDITIONER SEASON MAINTENANCE BEFORE AIR CONDITIONER SEASON 1 Operate the unit in the COOL mode, temperature setting 32°C, 2 3 for about half a day to allow the mechanism to thoroughly dry. Turn off the circuit breaker, if you have one exclusively for the air conditioner. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP GS-XP24ER

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP GS-XP24ER will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag