User manual SHARP HT-CN400DVE

[. . . ] When the ON/STAND-BY button is set at STAND-BY position, the unit may be brought into operation by the remote control. This unit contains no user serviceable parts. Never remove covers unless qualified to do so. This unit contains dangerous voltages, always remove mains plug from the socket before any service operation and when not in use for a long period. [. . . ] Use the button to skip to the previous chapter (track). On DVD, SVCD, VCD and Audio CD, press the button to skip to the beginning of the current track. Press the button again (twice) to skip to the beginning of the previous track/chapter. 1 Whilst in the stop or playback mode, press the PROG button. Track 01/23 TV screen CH: CH: CH: CH: CH: Exit 6 7 8 9 10 TT: TT: TT: TT: TT: 01:18 Program : Track (01-23) 1 2 3 4 5 Reset TT: TT: TT: TT: TT: CH: CH: CH: CH: CH: NEXT Notes: Some discs do not display the chapter (track) and the skip feature is disabled. On a DVD, skip does not operate between titles. Alternatively, press the or button on the main unit. Continued to the next page E-28 - Basic operation - Notes: DVD Operation 2 Press the PLAY/PAUSE playback. button to return to the normal HT-CN400DVE Basic operation (continued) 2 Enter title or chapter number with the Direct Number buttons. To specify title or track 1, enter "01" (must use 2 digits). If you enter the wrong numbers, press , or 9 button to select the concerned track and then re-enter the new numbers. To clear all the numbers those entered, press 9 button to select "Reset" and then press ENTER button. TV screen Press 9 button to select "Start" and then ENGLISH In the playback mode 1 Whilst in the playback mode, press the DIRECT button. TV screen 3 2 3 Select the title or chapter by pressing the 8 or 9 button and press the ENTER button. Enter the title or chapter number using the Direct Number buttons. To select chapter 1: Press "0" and "1". To select chapter 12: Press "1" and "2". Playback starts after you complete enter the number(s) (bottom). press ENTER button to start playback the programmed track(s). 1 2 3 4 TT: 01 CH: 02 TT: 02 CH: 02 TT: TT: CH: CH: CH: Exit 6 7 8 9 TT: TT: TT: TT: CH: CH: CH: CH: CH: NEXT TT: 5 Reset 10 TT: Start To change the programmed contents: 4 DVD Operation Repeat the above procedures from step 1. Press the DIRECT button to return to the actual size of image (standard screen). - Basic operation - Programmed contents will be cleared when you perform the following operations: Switch the input or remove the discs. The actual procedure for using the title menu depends on the disc. See the disc jacket for details. This starts A-B repeat from the start point (A) to the end point (B). 3 Press the A - B button to return to the normal playback. To select a subtitle or audio language from the disc menu You can select the desired subtitle or audio language and sound system [Dolby Digital (5. 1ch) or DTS sound] on your DVD if it has a disc menu. Notes: A-B repeat play is disabled on some discs. A-B repeat play for DVD is possible only within a title. A-B repeat play for SVCD/VCD/CD/MP3/DivX is possible only within a track. Some scenes on DVD may not allow A-B repeat play. 1 2 Whilst in the stop or playback mode, press the TITLE/RETURN button to display the disc menu. Example 1. Highlights 2. Start Movie Press the 8, 9, ; or : button to change the setting and press the ENTER button. Or use the Direct Number buttons for some discs. Note: The procedure shown here provides only general steps. The actual procedure for using the disc menu depends on the disc. See the disc jacket for details. E-33 Various settings The subtitle language, audio language and TV type you select during playback are reset each time you set this unit to the stand-by mode or switch the input. To keep your own settings, set them in the setup menu (see page 19). HT-CN400DVE ENGLISH To change the subtitle language You can change the subtitle language or hide subtitles during playback. ON STAND-BY OPEN CLOSE Whilst a disc is playing, press the SUBTITLE button repeatedly to select the desired subtitle SUBTITLE 01/03: ENGLISH language. Notes: On some discs, the subtitle language cannot be changed. If no subtitles are recorded on the disc, " " is displayed. It may take time to switch the subtitle language to the selected one. [. . . ] If the unit is not restored in the previous operation, unplug and plug in the unit, and then turn the power on. The preset channel cannot be recalled. P. 44 When the protection circuit is activated: When short-circuiting the speaker leads or turning the volume too high, the protection circuit may be activated and the system may enter the stand-by mode. Unplug the unit and, after 15 minutes or more, plug it in again. Turn down the volume if set too high. Symptom The remote control does not operate properly. Possible cause Is the battery polarity respected? [. . . ]