User manual SHARP HT-CN550DVW3

[. . . ] HT-CN550DVW3 ENGLISH ENGLISH Introduction Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. HT-CN550DVW3 Home Theater with DVD consisting of HT-CN550DVW3 (main unit), CP-CN550F (front speakers), CP-CN550C (centre speaker), CP-CN550R (surround speakers) and CP-CN550SW (subwoofer). Special notes WARNING CAUTION This product is classified as a CLASS 1 LASER product. [. . . ] To select title or chapter 22: Press " 2" and "2". ENGLISH In the playback mode 3 1 Whilst in the playback mode, press the DIRECT button. TV screen press ENTER button to start playback the programmed track(s). 01 02 03 04 TT: 01 CH: 02 TT: 02 CH: 02 TT: TT: CH: CH: 06 07 08 09 TT: TT: TT: TT: CH: CH: CH: CH: CH: 05 TT: Reset Exit 10 TT: CH: Start Next DVD Operation To change the programmed contents: Repeat the above procedures from step 1. 2 3 Select the title or chapter by pressing the the ENTER button. or button and press - Basic operation - Programmed contents will be cleared when you perform the following operations: Switch the input or remove the discs. Set to the stand-by mode. Enter the title or chapter number using the Direct Number buttons. To select chapter 1: Press "0" and "1". To select chapter 12: Press "1" and "2". Playback starts after you complete enter the number(s). To select and play the desired title and chapter: In the stop mode To start playback from the desired point (direct play) Whilst in the stop mode, press the DIRECT button. TV screen 4 Press the DIRECT button to return to the actual size of image (standard screen). Notes: Direct play feature is disabled on some discs. Some discs may not display the chapter number. With DVDs, you can specify the desired point only in the current title and not in another title. 1 TITLE 01/02 CHAPTER 001/002 2 Within 10 seconds, enter the title number first then only can enter the chapter number by using the Direct Number buttons. You can also press or button at this time for title or chapter selection. E-29 Useful operation To play by specifying time (time search): You can playback from the desired point by specifying the time. HT-CN550DVW3 ENGLISH ON STAND-B Y OPEN CLOSE 1 Whilst in the playback mode, press the DIRECT button. TV screen PRESE T MUTE PRESE T SLOW SLOW PLAY PAUS E OSD PLAY PAUS E TUNING STOP TUNING FUNC TION SETUP 2 3 Press or button. button to select "TT Time" then press the ENTER MENU PBC ENTER TITLE RETURN Specify the time with the Direct Number buttons. Track Time 1 :2 3 :4 0 You can slow down the playback speed. To specify 1 hour 23 minutes and 40 seconds, enter "12340". If you enter the wrong number, start over from step 1. Playback starts after you complete enter the number(s). On DVD, the speed changes as follows: 4 Press the DIRECT button to return to the actual size of image (standard screen). SLOW forward play 1/2 PLAY (Normal play) 1/16 SLOW reverse play On SVCD/VCD/DivX, only forward play is possible and the speed changes as follows: 1/4 1/8 1/16 Notes: Some discs cannot play from the specified point. Time search feature is disabled on some discs. 1/8 1/4 1/2 1/2 PLAY (Normal play) 1/4 1/8 1/16 2 Press the PLAY/PAUSE playback. button to return to the normal Note: On some discs, the slow-motion play functions are disabled. DVD Operation 1 Whilst a disc is playing, press the SLOW select the desired speed. button repeatedly to E-30 - Basic operation / Useful operation - Slow-motion play HT-CN550DVW3 Useful operation (continued) To change the angle ON STAND-BY OPEN CLOSE PRESET MUTE PRESET ENGLISH You can change the angle of view when playing a DVD disc that contains scenes recorded from multiple angles. SLOW PLAY PAUSE OSD When " " is displayed in the upper right corner of the TV screen, press the ANGLE button repeatedly to select the desired angle number. Notes: The angle number is not displayed if angles are not recorded on the disc. Refer to the manual of the disc as the operation may vary depending on the disc. TUNING STOP TUNING FUNCTION SETUP MENU PBC ENTER TITLE RETURN You can magnify images during playback. To zoom images (zoom) Whilst a disc is playing, press the ZOOM button. Each press of the ZOOM button cycles through the zoom settings as follows: 1 1 2 5 8 0 MIC LISTENING 3 6 9 PROG DVD Operation 4 7 EQUALIZER - Useful operation - 2X 3X 4X 1/2 1/3 1/4 OFF 2 VOLUME ECHO MODE ZOOM AUDIO SUBTITLE ZOOM ANGLE To shift the view and display the desired part of a zoomed image, press the , , or button repeatedly. ANGLE SLEEP DIRECT REPEAT A-B To return to normal view: Notes: Press the ZOOM button repeatedly. Images may become distorted when zoomed. Subtitles cannot be zoomed. E-31 HT-CN550DVW3 ENGLISH 1 ON STAND-BY OPEN CLOSE PRESET MUTE PRESET Whilst a disc is playing, press the REPEAT button. TV screen Unit display CHAPTER REP 1 STOP SLOW PLAY PAUSE OSD TUNING STOP TUNING FUNCTION SETUP Each time the button is pressed, the repeat play mode changes in the following order. The repeat play mode changes as follows on DVD: MENU PBC MENU PBC ENTER TITLE RETURN " ENTER CHAPTER" TITLE" ALL" "REP 1" "REP" "REP" Repeat the currently playing chapter. Repeat the currently playing title. " " 1 4 7 EQUALIZER 2 5 8 0 3 6 9 PROG 4 7 5 8 0 6 9 " " TRACK" ALL" "REP 1" "REP" No display MIC LISTENING Repeat the currently playing track. The normal playback. ECHO MODE VOLUME AUDIO SUBTITLE ZOOM ANGLE REPEAT "REPEAT OFF" SLEEP DIRECT REPEAT A-B A-B The repeat play mode changes as follows on audio CD: Repeat the currently playing track. Repeat the currently " ALL" "REP" playing disc. Randomly play the "SHUFFLE" "SHUFF" track The normal playback. "REPEAT OFF" No display MP3, DivX and JPEG are displayed when menu screen is "ON" (see page 39). " TRACK" "REP 1" 2 To play repeatedly (repeat play) You can play a chapter (track) or a title repeatedly by specifying it during playback. When playing SVCD or VCD, cancel the P. B. C. [. . . ] Possible cause Is the battery polarity respected?Are there any obstructions in front of the unit?Is the remote control sensor exposed to strong light (inverter fluorescent light, direct sunlight, etc. )?Is the remote control for another equipment used simultaneously? [. . . ]