User manual SHARP HT-SB350(W)/

[. . . ] Wewntrz urzdzenia nie ma adnych elementów wymagajcych naprawy lub obslugi uytkownika. Nie wolno demontowa obudowy urzdzenia, poniewa stwarza to ryzyko poraenia prdem. Naprawy naley zleca autoryzowanym serwisom. Urzdzenie naley odlczy od sieci przed przystpieniem do jakiejkolwiek naprawy lub kiedy nie bdzie uywane przez dluszy czas. [. . . ] [When the power is on] Press the CLOCK/TIMER button. Within 10 seconds, press the or button to display the time. The time display will appear for about 10 seconds. Note: The "CLOCK" will appear or time will flash to confirm the time display when the AC power supply is restored after a power failure or unplugging the unit. If incorrect, readjust the clock as follows. To readjust the clock: Perform "Setting the clock" from step 1. If the "CLOCK" does not appear in step 3, step 4 (for selecting the 24-hour or 12-hour display) will be skipped. To change the 24-hour or 12-hour display: 1 Clear all the programmed contents. [Refer to "Factory reset, clearing all memory" on page 63 for details. ] 2 Perform "Setting the clock" from step 1. 1 2 3 Press the ON/STAND-BY button to turn the power on. Within 10 seconds, press the or button to select "CLOCK", and press the MEMORY/DIMMER button. 4 Press the or button to select 24-hour or 12-hour display and then press the MEMORY/DIMMER button. "0:00" "AM 12:00" "AM 0:00" The 24-hour display will appear. (0:00 - 23:59) The 12-hour display will appear. When setting the DVS mode to "WIDE" or "REFERENCE", the preset sound mode and Audistry (SOUND SPACE mode, MONO TO STEREO mode) are cancelled. (The NATURAL BASS mode and the INTELLIGENT VOLUME mode are not cancelled. ) Monaural signals do not generate surround effects. In case input signal is Dual mono type and DVS is set to "WIDE" or "REFERENCE", the sound may not be output correctly. When unit is turned on for the first time, selecting BASS mode using the SOUND MODE button will automatically set the DVS to OFF. Subsequently, when BASS mode is selected again, the DVS setting will follow the current user setting. When headphone is inserted, DVS setting and BASS/TREBLE setting, set earlier by user will be cancelled. However the DVS setting will not be recovered when the headphone is unplugged. HT-DV40H3 HT-DV50H3 Audistry sound mode ON The Dolby Virtual Speaker creates multichannel-like sound effects. Compared with the cinema mode, the bass sound level is slightly reduced. 3 1 2 5 8 +10 3 6 9 ENGLISH Enjoy a variety of sounds by each or any combination of the 4 modes. Press the SHIFT and desired mode button simultaneously. Press it again to cancel. The Dolby Pro Logic indicator also lights up if 2ch sound signals are detected. 6 4 7 0 9 OFF The Dolby Virtual Speaker is deactivated. Possible combinations SOUND SPACE When you select "SOUND SPACE" When you select "NATURAL BASS" When you select "INTELLIGENT VOLUME" When you select "MONO TO STEREO" When you select "DVS" NATURAL BASS :Enabled :Disabled INTELLIGENT MONO TO VOLUME STEREO E-32 Basic Operation HT-DV40H3 HT-DV50H3 ENGLISH Enjoying surround sound (sound mode) (continued) SOUND SPACE (Sound stage expansion) The 4 speakers create spacious stereo sounds. (The SOUND SPACE indicator lights up. ) NATURAL BASS (Bass sound expansion) The system's low-frequency characteristics realise the optimal bass sounds. [. . . ] Display Meaning E7 Malfunction of surround circuit. Place the unit away from noise source and plug the AC power lead into another wall socket. (*) ERROR The unit considers the DVD mechanism is defective. (*) FAN LOCK The cooling fan on the rear of the unit does not run. [. . . ]