User manual SHARP IM-DR80

[. . . ] AND IRELAND Important Introduction -Special Notes- SERVICE INFORMATION In the unlikely event of your equipment requiring repair, please use the supplied postage paid label to send your unit to the Sharp repair centre or contact the dealer or supplier from whom it was purchased. Where this is not possible, please visit our web-site www. sharp. co. uk/customersupport. Customers without internet access may telephone 08705 274277 during office hours (or (01) 676 0648 if telephoning from Ireland). Please note; all calls will be charged at local rate. [. . . ] Press the or button repeatedly to select "DISPLAY". Press the or button. Each time the or button is pressed, the display will change as follows. Track name Elapsed playback time Remaining playback time 1 2 3 4 Whilst in the stop mode, press the MENU/ ENTER button. Press the or button repeatedly to select "DISPLAY". Press the or button. Each time the or button is pressed, the display will change as follows. Disc name Remaining recording time Total playing time Useful Features -Checking Displays- A A B B C C Notes: " If the disc name or the track name was not originally recorded on the MiniDisc, "NO NAME" will be displayed. " Elapsed playback time and remaining playback time may be different from the actual time. " The selected display will not change even after the disc is replaced. Notes: " Remaining recording time varies depending on the set recording mode. " Remaining recording time will not be displayed with a playback only MiniDisc. 28 IM-DR80 TINSE0562AWZZ 03/7/21 IM-DR80_4. fm IM-DR80 !To display the playing time of an individual track !Checking the remaining amount of battery level The remaining amount of battery level is shown by the battery indicator ( ) during operation. 1 Whilst in the stop mode, press the or button to display the track number and track name. Track number Track name How to read the battery indicator Useful Features 2 3 4 5 Press the MENU/ENTER button. " #$%& >?@_ ` ' ( k l mn o pq r KLMNOPQR ABCDEFGH STUVWXYZ. Lower-case letters D L a t 1 b u c d e f y 6 / s D L vwx hi z. , 7 : g Numbers and symbols ) D L * 2345 +, . 890 ;<= Notes: " One disc name and up to 255 track names can be created per disc (a maximum of 40 characters for the disc and each track name and a total of about 1, 700 characters can be entered). " If you enter "LP:" at the beginning of a name, "LP:" may not be displayed. 6 5 4 3 2 1 (Delete) : erases a character. (Space) : indicates a space. 31 IM-DR80 TINSE0562AWZZ 03/7/21 IM-DR80_5. fm IM-DR80 Titling a MiniDisc (continued) !Stamping titles from another MiniDisc Before stamping When there are 2 MiniDiscs on which the same tracks are recorded, you can transfer the character information (disc and track names) of the master MiniDisc to another MiniDisc (for stamping). 1 2 Put the unit in the character input mode. (Perform steps 1 - 5 on page 30. ) Advanced Features Press the VOL + or VOL - button to move the cursor to the character before which you want to add a new character. 1. What is a master MiniDisc? -Titling a MiniDisc- 3 4 Select the character to add. (Perform steps 6 - 8 on page 30. ) Press and hold down the MENU/ENTER button for 2 seconds or more. " "TOC" will be displayed. To write the updated contents to the MiniDisc, press the :OFF/HOLD button. " You cannot remove the MiniDisc whilst "TOC" is displayed. "TOC" will not disappear until the recorded contents have been updated. A recordable MiniDisc that contains tracks and character information. (You cannot transfer the information from a playback-only MiniDisc. ) 2. What is a MiniDisc for stamping? A MiniDisc that contains the same tracks in the same order as the master MiniDisc. [. . . ] If the plugs or sockets are dirty, noise may be heard. Cleaning will prevent noise. References 8 6 5 4 3 2 1 To remove condensation: Remove the MiniDisc and leave the unit for approximately 1 hour. The condensation should evaporate and the unit will work properly. 49 IM-DR80 TINSE0562AWZZ 03/7/21 IM-DR80_6. fm IM-DR80 Specifications As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. [. . . ]