User manual SHARP KB-3300JS

[. . . ] See Figures 1 and 2. 30" Freestanding Range ELECTRIC RANGE WITH MICROWAVE DRAWER CLEARANCES AND DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORTANT NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 3 ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 BACKSPLASH INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ANTI-TIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 MODEL AND SERIAL NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 CARE, CLEANING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . 8 1 INSTALLATION MANUAL RANGE MEASUREMENTS 29 7/8" 30" minimum 30" to bottom of cabinet over cooktop 29 5/8" adjustiable backspash width 18" to upper cabinets 42-48" with adjustiable backsplash 36±1/8" to cooktop surface 42 5/8" drawer open 17 3/4" 7 3/8" 6 1/8" 36" countertop height 27" back to front of doors 2 1/2" 30" opening width Figure 1 45 3/8" oven door open 30" door widths Figure 2 Preferred electrical outlet area Figure 1 contains many range measurements for reference when planning your kitchen and/or range location. CLEARANCES & DIMENSIONS · Provide adequate clearances between the range and adjacent combustible surfaces. · Dimensions that are shown in Figure 2 must be used. Given dimensions provide minimum clearance. [. . . ] This range may be connected by means of permanent "hard wiring" (flexible armored or nonmetallic shielded copper or aluminum cable), or by means of a power supply cord kit. Only a power supply cord kit rated at 240 volts or 208 volts and 50 amperes and marked for use with ranges shall be used. Cord must have either 3 or 4 conductors to match electric receptacle. For mobile homes, new installations, recreational vehicles or areas where local codes do not permit grounding through neutral, a 4 conductor power supply cord kit rated at 240 volts or 208 volts minimum, 50 amperes and marked for use with ranges should be used. Terminals on end of wires must be either closed loop or open-end spade lugs with upturned ends. The range connection opening should be 1 3/8-inches. Risk of fire or electrical shock exists if an incorrect size range cord kit is used or the Installation Manual or strain relief clamp are disregarded. CAUTION Do not loosen the nuts which secure the factoryinstalled range wiring to the terminal block while connecting range. Electrical failure or loss of electrical connection may occur. ELECTRICAL SHOCK HAZARD · Electrical ground is required on this range. · Do not connect to the electrical supply until range is permanently grounded. · DISCONNECT POWER TO THE CIRCUIT BREAKER OR FUSE BOX BEFORE MAKING THE ELECTRICAL CONNECTION. · This range must be connected to a grounded, metallic, permanent wiring system or the grounding connector of the power cord should be connected to the grounding terminal or wire lead on the range. Tighten all 3 or 4-wire leads to the terminal block. Follow wire locations shown in Figure 10. IMPORTANT DO NOT LOOSEN the factory installed nut connections which secure the range wiring to the terminal block. Electrical failure or loss of electrical connection may occur if these 3 nuts are loosened or removed. A ground strap is installed on this range which connects the center terminal of the neutral terminal block to the range chassis. The ground strap is connected to the range by the center, lowest screw. The ground strap must not be removed unless National, State or Local Codes do not permit use of a ground strap. Note: If the ground strap is removed for any reason, a separate ground wire must be connected to the separate ground screw attached to the range chassis and to an adequate ground source. 3 & 4-WIRE PERMANENT WIRE CONNECTIONS Note: For 3-wire permanent connection skip steps 3 and 4 and continue with step 5. 3 Disconnect the ground strap. Remove the factory installed ground screw and plate to release the factory installed copper ground strap from frame of the range. Cut and discard the copper strap from the terminal block. KEEP the ground screw, ground plate and go to step 4. 4 Connect the green ground wire lead to the frame of the range using the ground screw and plate as shown in Figure 11. Be sure to install using the same hole in the frame where the ground screw was originally installed. [. . . ] When installed to the wall, make sure that screws completely penetrate dry wall and are secured in wood or metal. When fastening to the floor or wall, be sure that screws do not penetrate electrical wiring or plumbing. 1 LOCATE THE BRACKET - USING THE TEMPLATE Drill a 1/8-inch pilot hole where screws are to be located. If bracket is to be mounted to the wall, drill pilot hole at an approximate 20 degree downward angle. If bracket is to be mounted to masonry or ceramic floors, drill a 5/32-inch pilot hole 1 3/4-inches deep. [. . . ]