User manual SHARP LC-13C2M

[. . . ] 4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing Batteries in the Remote Control . . . . . . . . . . . . . . . . . . . 5 Using Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] is turned blue when there is no signal. * Backlight setting can be switched in one touch using the remote control (see right). NOTE · Select "Timer function" and press OK to set "Sleep timer" and "Wake-up timer" (See page 21). · When all adjustments set to factory preset values, 1 Press '/" to select "Reset", and press OK. 2 Press \/| to select "Yes", and press OK. 20 Basic Adjustment Settings (Continued) Timer Function 1 2 3 Press MENU to display the Menu screen. · The Timer function Menu screen can be displayed directly by pressing the Yellow. Press \/| to select "Features". Press '/" to select "Timer function", and press OK. F B T A B R M e a i u l e e a c m t u s n t k e o e e u[Features ures light r function power off back t Timer function] 4 Press '/" to select "Sleep timer", and press OK. Menu[Features Sleep timer Wake-up timer Timer function] ­­­ Selected Off 3 0 min 6 0 min desired item 9 0min 12 0 min 15 0 min 5 6 : SELECT O K : ENTER M : BACK E : Press '/"/\/| to select "Off", EXIT "30min", "60min", "90min", "120min" or "150min", and press OK. Press '/" to select "Wake-up timer", and press OK. Menu[Features Sleep timer Wake-up timer S W C V e a h o Timer function] setting O 0 C 2 ff 0:0 0 H1 0 Adjust t ke-up annel lume time 7 8 : SELECT O K ENTER M : desired adjustment item, and Press '/" to:select the BACK E : EXIT press \/| to adjust them. Press OK to set. Press MENU to exit. NOTE · When you set "Wake-up timer", POWER indicator lights up orange. · Be sure to adjust the clock with "Clock setup" in "Setup" before setting "Sleep timer" and "Wake-up timer". · Timer programming settings are cancelled when the duration of the power outage exceeds the backup time. (See page 14. ) 21 NICAM Broadcast Selection To let you enjoy NICAM broadcasting, this LCD TV receives NICAM stereo system, bilingual, and monaural broadcasts. If the sound quality is poor due to a weak signal or other problems during NICAM broadcast reception, set the "Off" position of the NICAM to change the TV sound to monaural. Stereo The LCD TV set is receiving a stereo broadcast. · Each time you press MPX, the mode changes between "NICAM STEREO" and "MONO". · When "MONO" is selected, the TV sound is output monaurally. (When stereo sound is received) 1 2 3 Press MENU to display the MENU screen. Press TEXT and the Teletext screen is displayed. 100 TELETEXT TELETEXT Red Green Yellow Cyan Red Green Yellow Cyan Operating instructions in Teletext mode · The FLOF system for teletext is transmitted in Singapore currently. · The TOP system for teletext is transmitted in Australia currently. · If TOP Teletext is broadcast, a control line and TOP line can be displayed on the screen. The TOP line involves the operating instructions associated with all of the Coloured buttons if TOP text is transmitted, or the operating instructions for only Red and Green if TOP text is not being transmitted. · If there are subpages, a control line holding the operating instructions for subpages can be displayed on line 24. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 369 SHARP - T EXT 02 : 5 2 : 21 To turn off the Teletext mode, press TEXT again. [2] Using the TOP line When TOP Teletext is being broadcast, you can display the TOP line, which contains the operating instructions on the screen. 1 100 200 Press the Coloured buttons to operate the Teletext screen. · Press Red to display the previous page and Green to display the next page. Yellow and Cyan are as indicated on the TOP line. NOTE · By pressing Red the previously selected page will appear down to the first page which showed up directly after switching on the teletext. Therefore Red has no function directly after switching on the teletext. 24 Teletext (Continued) [3] Changing subpages If a page has been selected from among several subpages, you can display a control line which contains the subpage numbers. [5] Using Teletext menu To select the character set 1 1 Press SUBPAGE. The control line with the subpage numbers is displayed on line 24, and the number of the currently selected subpage is displayed in blue. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 369 SHARP - T EXT 02 : 5 2 : 21 During Teletext broadcast, press MENU to display the "Character set" screen. Character A W E T r e a u a s s r bic/H t Eur t Eur kish/ e o o G b p p r set rew e e eek 2 Press '/" to select the desired character set. · The colour of the letters will turn to yellow. [. . . ] · Bad reception could be the problem. Picture is not clear. 6 ­ Picture is too light or improperly tinted. · Check colour adjustment. (NTSC mode) 16 The picture is too dark. · Check if "Backlight" is set to "Dark". · The fluorescent lamp may have reached the end of its service life. 20 16 ­ Remote control does not work. · Check if batteries in the remote control have sufficient power. [. . . ]