User manual SHARP LC-32/37/42WD1E/S/WT1E

[. . . ] LC-32WD1E LC-32WT1E LC-32WD1S LC-37WD1E LC-42WD1E LC-37WT1E LC-42WT1E LC-37WD1S LC-42WD1S LCD COLOUR TELEVISION LCD-FARBFERNSEHGERÄT TÉLÉVISION COULEUR À ÉCRAN À CRISTAUX LIQUIDES (LCD) TELEVISORE A COLORI LCD LCD-KLEURENTELEVISIE TELEVISIÓN EN COLOR LCD ESPAÑOL OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUALE DI ISTRUZIONI GEBRUIKSAANWIJZING MANUAL DE MANEJO NEDERLANDS ITALIANO FRANÇAIS DEUTSCH ENGLISH SPECIAL NOTE FOR USERS IN THE U. K. The mains lead of this product is tted with a non-rewireable (moulded) plug incorporating a 5A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug, must be used. Always re t the fuse cover after replacing the fuse. [. . . ] Press Press / / to select Setup Menu, and then press OK. to select Overview, and then press OK. If you have a PIN set in Child Lock, enter it now using 0­9. The Overview Menu displays. Fine Sync Menu Operation: C (page 12) The Fine Sync setting allows you to manually adjust the image on the TV. Adjusts the screen if the image flickers with vertical stripes. Automatically adjusts the screen if text has low contrast or if the image flickers. Resets the settings to the factory default. Reset 5 Press · · /// to select the channel. NOTE: · To delete the channel, press RED. Press / / / to go to the desired new position. Press GREEN again to place the channel in the new position. Similar adjustments are available on your computer. 17 Menu operations (main) Input Label The Input Label setting allows you to customize the label that is displayed for each input source. Clock Menu Menu Operation: C (page 12) The Clock Menu setting allows you to set a 12-hour or 24hour clock and set the time manually. to set this setting to 12 Hours or 24 1 2 3 4 5 Press to select the input source whose label you want to change. With the input source selected, press MENU. Press Press / / to select Setup Menu, and then press OK. to select Input Label, and then press OK. · NOTE: · Press / to select Set Time. Press 0­9 to enter the current time. If teletext information is available, the TV will automatically synchronize with the time included with the teletext information. Use / / / to enter each letter of the new name, and then press OK. · · The name can be six characters or less. You cannot change the label if the input source is TV or DTV. TV/DTV/AV only NOTE: Option Menu Position Menu Operation: C (page 12) The Position setting adjusts the horizontal and vertical position of the image on the screen. Resets the settings to the factory default. WSS (Wide Screen Signalling) Menu Operation: A (page 12) TV/DTV/AV only Input Select Menu Operation: A (page 12) The TV will automatically detect the type of input for EXT1, EXT2, or EXT3. However, this can be set manually if desired. (For example if the image is unclear. ) EXT 1, EXT 2 EXT 3 Y/C (S-Video), RGB, CVBS Y/C (S-Video), CVBS If the incoming broadcast contains wide screen signals, the WSS setting allows the TV to automatically switch to the appropriate screen format. NOTE: · To adjust the wide screen format manually, see "Wide Mode" on page 20. Antenna Supply Voltage Menu Operation: A (page 12) The Antenna Supply Voltage setting turns power "On" or "Off" to the antenna input connection on the rear of the television. (See page 3. ) Audio Only Menu Operation: A (page 12) The Audio Only setting turns off video and only plays the audio from the source. DNR (Digital Noise Reduction) Menu Operation: C (page 12) TV/DTV/AV only The DNR setting (Digital Noise Reduction) produces a clearer image by reducing digital noise. [. . . ] Model numbers: LC-32WD1E, LC-32WT1E, LC-32WD1S b. Model numbers: LC-37WD1E, LC-37WT1E, LC-37WD1S c. Model numbers: LC-42WD1E, LC-42WT1E, LC-42WD1S As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. [. . . ]