User manual SHARP LC-42DH77V

[. . . ] In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below: IMPORTANT: The wires in the mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: · The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black. · The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red. [. . . ] Depending on the manufacturer and type of equipment used, it is possible that the described functions may be completely or partially unusable. 17 Connecting external devices Speaker/amplifier connection Connect an amplifier with external speakers as shown below. E Connecting an amplifier with digital audio input E Connecting an amplifier with analogue audio input DIGITAL AUDIO OUTPUT R-AUDIO-L OUTPUT Optical AUDIO cable Audio cable R L R L DIGITAL AUDIO IN AUX1 IN AUX OUT Amplifier with digital audio input E After connecting Digital audio output setting After connecting an amplifier with digital audio input and external speakers as shown, you should set an audio output format compatible with the programme you are watching or the device connected. Go to "MENU" > "Option" > "Digital Audio Output" > select "PCM" or "Dolby Digital". Amplifier with analogue audio input 18 Connecting external devices Inserting a CA Card In order to receive coded digital stations, a Common Interface Module (CI Module) and a CA Card must be inserted in the CI slot of your TV set. (Page 8) The CI Module and the CA Card are not supplied accessories. They are usually available from your dealer. Checking CI Module information NOTE · Make sure that the CI Module is properly inserted. · This menu is only available for digital stations. 1 2 3 Press MENU and the "MENU" screen displays. Press c/d to select "Digital Setup". · The content of this menu depends on the provider of the CI Module. Inserting the CA Card into the CI Module 1 With the side with the gold coloured contact chip facing the side of the CI Module marked with the provider's logo, push the CA Card into the CI Module as far as it will go. Note the direction of the arrow printed on the CA Card. Press a/b to select "CI Menu", and then press OK. E Module General information on CI Module displays. E Menu Adjustment parameters of each CA CARD displays. E Enquiry You can input numerical values such as passwords here. NOTE · The content of each screen depends on the manufacturer of the CI module. Inserting the CI Module in the CI slot Removing the CI Module 2 Remove the rear terminal cover. 1 2 3 Remove the cover from the rear of the set. Replace the cover. 3 Carefully insert the CI Module in the CI slot with the contact side forward. The logo on the CI Module must be facing forward from the rear of the TV. Make sure the module is not bent in the process. 19 AQUOS LINK Controlling HDMI devices using AQUOS LINK What is AQUOS LINK? Using the HDMI CEC (Consumer Electronics Control) protocol, with AQUOS LINK you can interactively operate compatible system devices (AV amplifier, DVD, Blu-ray Disc device) using a single remote control. NOTE · The factory default for this item is "Off". 1 2 3 Repeat steps 1 to 3 in AQUOS LINK Auto power on. Press a/b to select "Selecting Recorder", and then press OK. Select the recorder, and then press OK. NOTE · If you have connected the AQUOS AUDIO speaker system between the TV and an AQUOS Recorder, the external source's indication changes from "EXT5" to "EXT5 (Sub)". Using Genre Info. This function allows you to automatically switch to the appropriate sound mode depending on the genre information included the digital broadcast. 1 Repeat steps 1 to 3 in AQUOS LINK Auto power on. 2 Press a/b to select "Using Genre Info. ", and then press OK. 3 Press c/d to select "On", and then press OK. 21 Selecting recorder Here, you can select a recorder for the recording from several connected recorders. AQUOS LINK Operating an AQUOS LINK device AQUOS LINK allows you to operate the HDMIconnected device with one remote control. 1 Open the remote control's flip cover. 2 Press PLAY I to start playback of a title. · See the right column, section "Playback of titles using AQUOS LINK" if you want to start playback using the list of the titles of the AQUOS BD Player/ AQUOS Recorder. Playback of titles using AQUOS LINK This section explains how to play back a title in the AQUOS BD Player/AQUOS Recorder. 1 Open the remote control's flip cover. 2 Press OPTION. · The AQUOS LINK Menu displays. 3 Press a/b to select "Top Menu/Title List", and then press OK. · The linked recorder now powers on and the TV automatically selects the appropriate external input source. [. . . ] Please purchase them at your nearest shop. · Additional optional accessories may be available in the near future. When purchasing, please read the newest catalogue for compatibility and check the availability. 1 Part name Wall mount bracket Part number AN-52AG4 When using Wall-mount bracket AN-52AG4 · Wall bracket B has an attachment pitch of 400 mm. · Assemble wall brackets using mark "C" on wall bracket A and mark "A" on wall bracket B. [. . . ]