User manual SHARP MD-R2

[. . . ] MINIDISC DECK OPERATION MANUAL MODEL MD-R2 Thank you for purchasing this SHARP product. For the best performance, read this manual carefully. It will guide you in operating your SHARP product. FOR YOUR RECORDS For your assistance in reporting this unit in case of loss or theft, please record below the model number and serial number which are located on the rear of the unit. Model number ___________________________ Serial number ___________________________ Date of purchase ________________________ Place of purchase ________________________ CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTI ON: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NO T REM O VE CO VER (OR BACK). [. . . ] This feature is different from program play. A new track order can be recorded directly on the disc. When the power is turned off, the revised order will not be changed. (Page 24) 1 2 3 4 A 1 2 B 3 C 4 D 1 A 2 B 3 C 4 D A B C D C A B D COMBINE Two adjacent tracks (for example, the third and fourth tracks) can be combined. If there is a prolonged silent section in the middle of a selection that is recorded, a single piece of music may be recorded as two tracks. If this happens, these two tracks can be combined into a single track. (Page 23) Program move function This function allows the track numbers to be automatically rearranged in the order specified for programmed playback. The track numbers will be adjusted as needed, automatically. (The tracks that are not included in the programmed selections will be put at the end of the new track numbers. ) (Page 24) 1 2 3 4 1 2 3 4 A 1 2 B 3 C D 1 A 2 B 3 C 4 D A B C D C A D B ERASE Tracks you want to erase can be erased one at a time or all at once. Once a track has been erased, it cannot be recovered. Double-check the track number before erasing it. (Page 25) TRACK/DISC NAME You can assign titles to recorded tracks and to discs. The characters must be capital and lowercase letters, or symbols. Track and disc names can use up to 100 characters per name. (Page 26) 1 2 3 4 5 A 1 2 B C 3 4 D E TOC DISC 4 TOTAL 1234567 8 9 10 11 12 13 14 15 16 17 18 A B D E 20 MD-R2 (Continued) s Using the editing function We will show you some examples of how to use the editing functions. You can create a disc of your favorite selections by recording tracks from a variety of input sources such as CDs, tapes, and radio broadcasts. STEP 1 Recording tracks to be edited on an MD Digital recording from a CD Recording a broadcast Analog recording from tape A B C D D Talk E Live performance STEP 2 Putting the space between tracks in order A B C D D Talk E Live performance The tracks are combined using the combine function. A B C D The tracks are divided using the divide function. Talk E F G CM H STEP 3 Cutting unnecessary sections Cut using the erase function. Cut using the erase function. G H STEP4 Rearranging tracks in your preferred order A B C D E F The tracks are rearranged using the program move function. D E A C B H The track is moved using the move function. F G STEP 5 Finish by putting names on the disc and tracks (Disc name) (Track name) The editing functions are selected from the edit menu. The functions which can be selected from the edit menu will vary, depending on the state in which an editing operation is started. STEP 1 Edit menu display NAME/TOC EDIT STEP 2 Edit menu selection Previous menu Next menu STEP 3 Editing start ENTER Each time the button is pressed, the edit menu will appear. (Move function) Each time the dial is turned, the menus will appear in order. (Track name function) You can edit the selected menus. A different menu may be displayed. Within 10 seconds, perform step 3. To stop editing anytime, press the button. This function Can be selected in the following conditions. ( Disc name Track name Divide Combine Move Program move Erase All erase When stopped The total number of tracks appears )( When stopped Selection of track numbers ) During playback Playback in the pause mode During recording/ in the recording standby mode When entering a program 21 MD-R2 (Continued) s DIVIDE ENTER NAME/TOC EDIT 1 Play the track which you want to divide into two, and press the 06 button at the point where you want to divide the track. q The unit will enter the pause mode. 2 Press the NAME/TOC EDIT button, and then select "DIVIDE" using the jog dial. 3 Within 10 seconds, press the ENTER button. [. . . ] The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. q General Type: Signal readout: Audio channels: Frequency response: Rotation speed: Error correction: Coding: Recording method: MiniDisc deck Non-contact, 3-beam semi-conductor laser pick-up Stereo 2 channels/monaural (long-play mode) 1 channel 4 ­ 20, 000 Hz (+0/-1 dB) Approximately 400 to 900 rpm ACIRC (Advanced Cross Interleave Reed-Solomon Code) ATRAC (Adaptive TRansform Acoustic Coding) Magnetic modulation overwrite method A/D, D/A converter: Sampling frequency: Wow and flutter: Signal/noise ratio: Power source: Power consumption: Dimensions: Weight: 1-bit 44. 1 kHz Unmeasurable (less than ±0. 001% W. peak) 100 dB or better during playback (line output) AC 120 V, 60 Hz 17 W Width: 16-15/16" (430 mm) Height: 3-11/16" (93 mm) Depth: 11-15/16" (302 mm) 8. 0 lbs (3. 6 kg) Input jacks Jack name LINE IN Jack shape Pin jack Input impedance Over 22 kohms Reference input level 680 mVrms Minimum input level 170 mVrms Output jacks Jack name Jack shape Output Load level impedance 15 mW 2 Vrms 32 ohms 50 kohms PHONES 1/4" (6. 3 mm) stereo (Headphones) jack LINE OUT Pin jack OPTICAL Square IN (Optical) optical connector COAXIAL (Coaxial) Pin jack 75 ohms 500 mVp-p OPTICAL Square optical connector OUT (Optical) q Timer/clock Type: Timer: Digital clock with date function ON/OFF, once a day q Remote control Power: DC 3V ("AA" (UM/SUM-3, R6, HP-7 or similar) battery included x 2) 38 MD-R2 LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below. This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to misuse, abnormal service or handling, or which has been altered or modified in design or construction. [. . . ]